Kodak 8650 manual Metal roller bar Metal bar Header line

Page 22

Setting up the printer

4.To clean the print head, first use the water pad and then use the alcohol pad. With each pad, wipe along the heater line four times as follows:

—Wipe the full length of the glass area (always in one direction). —Use a clean part of the pad for each wipe.

—Apply firm, even pressure.

—Wipe the metal roller bar and rod as shown.

Metal roller bar

Metal bar

Header line

AVOID METAL

EDGE!

Rod

5.Allow the glass area to dry for about two minutes.

6.Do one of the following:

If reloading the ribbon, load the supply spool first (with the bar code on the left. If the ribbon gets dirty or is damaged, wind the take-up spool ahead to the next clean magenta section.

If loading a new ribbon, refer to the instructions on the ribbon package.

7.Close the printer cover, and turn the printer On.

October 1997

2-7

Image 22
Contents Kodak Digital Science Part No H9657Radio Frequency Interference Regulatory Information Safety Regulations Table of contents Troubleshooting the printer Operating the printerAppendix C Customizing the printer Appendix a Printer specifications/site requirementsAppendix B Accessories and supplies IndexUsing this guide About this guideAbout the other guides included with the printer Getting help or additional information Introduction About printer memoryMedia and image size Paper/Transparency size Maximum image sizeInterface Type Version Printer Mode Interface Type Printer ModeInterfaces Printer drivers and export modules Fonts Resident fontsSetting up the printer Finding a location for the printer Unpacking the printer Remove the shipping tape from the printer cover Cleaning the print head Takeup spool Supply spool Metal roller bar Metal bar Header line Handling the ribbon Loading the ribbonStoring the ribbon Loading ribbon in the printer Take-up spool Supply spool Setting up the printer Storing media Unpacking and adjusting the paper trayWorking with media Paper and humidityHandling humidity-related paper problems Loading media Setting up the printer Setting up the printer Putting the dust cover on Connecting the cables Connecting a parallel cable Connecting a LocalTalk cableConnecting a Scsi cable Scsi ports Raster printing only Connecting the power cord Checking and changing printer settings Changing the operating modeChanging the media settings Changing the media typeChanging the paper color About printer initialization If the printer does not initialize itselfWhat’s next Operating the printer Looking at the display panel Operating the printer Working with the printer settings Printer settingsScsi Working in Setup mode About specifying port informationSpecifying the printer’s Scsi ID raster mode Specifying the Scsi connection PostScript modeWorking with media 2Kodak thermal paper types, sizes, and image size CAT No210 x 307 mm 217 x 307 mm 3Transparency material size and maximum image size CAT No 853 CAT No 163 210 x 358 mm Printing from computer applications Scheduling jobs Handling and storing prints and transparencies Cleaning the printer Keeping the printer in good working order Working with the printerTroubleshooting the printer Error messages and how to resolve them 1Common error messagesParallel connection only Other connectionsLoad Paper 2Machine Generated Error Codes Controller Printed Circuit Board 3Common error messages Error Description Possible solutionReceiver type mismatch When mismatches occurRibbon type mismatch Receiver size mismatchProblem Possible cause Possible solutions Solving common printer problemsIf the printer is not operating correctly Fingerprints have caused Clearing the paper path Troubleshooting the printer Troubleshooting the printer Cleaning the pick rollers Troubleshooting the printer Cleaning the sensors Important Before cleaning, turn off the printerRepacking the printer Shipping tape Getting additional help Country Country code Helpline numberAppendix a Printer specifications/ site requirements Printer dimensionsPrinter weight Printer specificationsOperating environment Power requirementsPower consumption Voltage/frequencyAccessories Appendix B Accessories and suppliesSupplies Ribbons Maximum Catalog Ribbon Type Image Size NumberPaper Paper Type Catalog Size NumberTransparency material Transparency Type Size NumberAppendix C Customizing the printer Installing the hard drive Adding an external hard driveInitializing the hard drive For Printing or PS Mode window appears Downloading additional fonts to the hard drive Disk Click Download Preparing to install a Simm Adding memory to the printerAppendix C Customizing the printer Appendix C Customizing the printer Appendix C Customizing the printer Installing the Simm card Finishing up Index CablesIndex Index Jams Index Index Index Scsi ID Index Index Kodak Canada INC