IBM 16/4 Token-Ring manual User Action None LA10033 Adapter analysis code is

Page 70

The possible remedies are to try to connect again at a later time when at least one other ring station is active on the network (such as a network server), or to change the configuration value so that the DataRate parameter is set to a specific ring-speed value of M16 or M4 and restart the computer.

Note that setting a specific value of M16 or M4 for the DataRate parameter will cause this adapter to establish the operational speed of the token-ring network if it is still the first active ring station.

This message is relevant for 4-Mbps or 16-Mbps operation only.

Check the adapter installation instructions for additional information on setting the DataRate parameter.

LA10024 The adapter attempted to perform a Remote Program Load but failed monitor contention.

Explanation: The adapter was opened as a Remote Program Load (RPL) client, but was unable to locate an RPL server on the network.

User Action: Make sure that there is an active Remote Program Load server on the network and that it is configured to recognize this adapter’s address.

LA10025 A network protocol error occurred while attempting to operate the adapter in full duplex mode.

Explanation: The adapter was unable to successfully communicate with a token-ring switch when attempting to open for full-duplex operation.

User Action: Check that your full-duplex switch is functioning correctly and that the adapter is correctly connected to it. If this problem persists, contact your support personnel.

LA10026 Unable to automatically change to xx Mbps operation. Please reboot the computer.

Explanation: The adapter attempted to open at one speed, but found the Token Ring operating at another speed. The configuration parameters used during initialization processing, notably the maximum frame size, preclude reliable operation at the new speed, so all additional attempts to open the adapter will be rejected. Rebooting the computer allows the new speed to be factored into the initialization processing without requiring a configuration change in most cases.

User Action: Shut down and restart the computer. Normally, no explicit configuration changes are required to begin operating at the current operational speed of the Token Ring. Optionally, you might be able to change the value of the configuration parameter that specifies the maximum frame size to a value of 4500 or less to eliminate the need to reboot the computer for a similar situation in the future.

LA10027 The adapter opened for token ring, xx Mbps., half duplex.

Explanation: Information only.

User Action: None.

LA10028 The adapter opened for token ring, xx Mbps., full duplex.

Explanation: Information only.

User Action: None.

LA10033 Adapter analysis code is xx.

Explanation: Information only.

User Action: None.

LA10034 Adapter full-duplex operation has now been activated.

Explanation: Information only.

User Action: None.

62IBM 16/4 Token-Ring PCI Management Adapter

Page 69 Page 71
Image 70
Page 69 Page 71
Contents User’s Guide First Edition April Contents Appendix A. CD-ROM content and software packages If YOU Download or USE this Program YOU Agree to These Terms Vi IBM 16/4 Token-Ring PCI Management Adapter Who should read this manual About this manualHow this manual is organized Related publications Adapter installation checklist Environment limitations on number of adapters Package contentsAutomatic Configuration and Power Interface Acpi Wake on LANPage IBM 16/4 Token-Ring PCI Management Adapter Installing the adapter Installing the adapter hardwareSelecting adapter cables STP and UTP cables Software installation Operating System Directory Novell NetWare 3.12 Server Environment DOS with Windows VersionServer driver installation in new NetWare 3.12 Server STARTUP.NCFServer driver installation in existing NetWare 3.12 Server Novell NetWare 4.11 Server Select Edit STARTUP.NCF File and press EnterServer driver installation in new NetWare 4.11 Server Server driver installation in existing NetWare 4.11 Server Software installation Novell NetWare 5.0 Server Server driver installation in existing NetWare 5.0 Server Select Driver Options → Configure network driversNovell Client DOS/Windows Select Save parameters and load driverOS/2 Ndis 2 device driver using Mpts OS/2 Ndis 2 device driver using other installation programs OS/2 Novell NetWare RequesterDOS Ndis DOS Novell NetWare Requester 16-bit Windows NT Version Select Start → Settings → Control Panel Windows IBM 16/4 Token-Ring PCI Management Adapter Select Finish to continue the installation Select Device Manager Installing the driver when Windows 98 is already installed Windows This wizard searches for updated drivers for Adapter name Updating the driver when Windows 2000 is already installed Novell IntranetWare Client for Windows NTNovell Client for Windows Windows for Workgroups with NdisRunning Managed Driver Upgrade locally Running Managed Driver Upgrade remotely Option ExplanationIBM 16/4 Token-Ring PCI Management Adapter Using Troubleshooting Utility Problem solvingStarting the troubleshooting process Symptom SolutionStarting Troubleshooting Utility Installing Troubleshooting UtilityWindow / Tab Task Viewing adapter analysis information Status NDIS8025RINGSTATE value Explanation Status NDISHARDWARESTATUS-type Explanation ValueStatus Viewing the event log Running adapter diagnostics Running 4/16 Mbps diagnosticsUnderstanding the adapter LEDs and labels Understanding the adapter LEDs Amber Green ExplanationAmber Green Explanation Action Solving problems with driver installationUnderstanding the adapter labels Environment Message Type and ActionUsing Pcisetup Solving an adapter communication problemDOS, Novell, Windows, or Windows 95 adapter driver not Windows NT Tech tips and frequently asked questionsOS/2 Contacting IBM product supportIBM 16/4 Token-Ring PCI Management Adapter Appendix A. CD-ROM content and software packages Operating System DirectoryPackage Description Executable Software packagesDiskette images Image Description ExecutableProduct documentation IBM 16/4 Token-Ring PCI Management Adapter Appendix B. Ndis 2 device driver parameters PROTOCOL.INI files, see on page 58 and onValid values 1 to Parameter ExplanationValid values 14 to 18,000 Valid values 256 to 18TxPriMax Valid values 0 toPeer DisableAuto Xxx.xxx.xxx.xxxValid values PortNumber PriorityValueSection a Protocol Driver IBM TCP/IP V1.2 for DOS TCPIPnif Appendix C. Ndis 2 device driver messages LA10001 IBM PCI Token-Ring Adapter, VersionIBM 16/4 Token-Ring PCI Management Adapter Appendix C. Ndis 2 device driver messages User Action None LA10033 Adapter analysis code is User Action NoneLA10044 The Ndis 2.0 Protocol Manager could not be opened LA10045 Could not find the PROTOCOL.INI file imageIBM 16/4 Token-Ring PCI Management Adapter Appendix D. Novell NetWare Server driver parameters Load Ibmtrpo line in the AUTOEXEC.NCF fileAdapter Features document Token-Ring Adapter Features document RTTS= Valid values 2 toParameter Explanation IBM 16/4 Token-Ring PCI Management Adapter Appendix E. Novell NetWare Server messages User Action None IBMTRPO-xx-203 Adapter is using an LAAIBMTRPO-xx-202 Adapter UAA BIA is IBM 16/4 Token-Ring PCI Management Adapter Appendix E. Novell NetWare Server messages User Action None IBMTRPO-xx-233 Adapter analysis code is IBMRNIC.NLM IBM 16/4 Token-Ring PCI Management Adapter Following parameters can be configured in the NET.CFG file Appendix F. Novell NetWare DOS ODI driver parametersValid values 9 to M16Valid values NO, YES Appendix G. Notices Trademarks Safety Information IBM 16/4 Token-Ring PCI Management Adapter Appendix G. Notices IBM 16/4 Token-Ring PCI Management Adapter Electronic Emission Notices Avis de conformité aux normes d’Industrie Canada Federal Communications Commission FCC StatementEuropean Norm EN Statement Hinweis zur Elektromagnetischen Verträeglichkeit Emvg Other Electronic Emission Notices for UTP MediaIndustry Canada Class a Emission Compliance Statement Appendix G. Notices IBM Power Cord Part Used in These Countries Number IBM License Agreement for Productivity AidsIf YOU Download or USE this Program YOU Agree to These Terms NetWare Network Computing Products from IBM Protection and SecurityLabel on documentation must also include the words Warranty Service Warranty Period* LifetimeIBM Warranty Production StatusExtent of Warranty Limitation of LiabilityIBM 16/4 Token-Ring PCI Management Adapter Glossary CRC. See cyclic redundancy check CRC Full-duplex. Synonym for duplexLAN. See local area network LAN Open Systems Interconnection OSI architecture Open Systems Interconnection OSI referenceSegment. See cable segment, LAN segment, ring segment IBM 16/4 Token-Ring PCI Management Adapter Index DOSMpts TXPRIMAX= Txprithresh
Top Page Image Contents