Fujitsu B120 No mouse pointer displayed on the screen, Floppy disk cannot be read or written

Page 49

No mouse pointer displayed on the screen

Troubleshooting and tips

7.6No mouse pointer displayed on the screen

Mouse driver not loaded

ÊCheck whether the mouse driver is properly installed and is present when the application program is started. Detailed information can be found in the User Guides of the mouse, the operating system or the application program.

Mouse controller disabled

The mouse controller on the system board must be enabled, if you use the supplied mouse.

ÊCheck in the BIOS Setup that the mouse controller is Enabled.

7.7The floppy disk cannot be read or written

ÊCheck whether the write protection of the floppy disk is activated.

ÊIn the BIOS Setup check the entry for the floppy disk drive.

ÊCheck in the BIOS Setup whether the diskette drive controller and write permission are enabled (see the Technical Manual for the system board).

ÊCheck that the cables of the floppy disk drive are properly connected (refer to chapter "System components and expansions").

7.8Time and/or date is not correct

ÊSet the time and/or date in the operating system or in the BIOS Setup.

i	If the time and date are repeatedly wrong when you switch on your server, the battery is
	flat. Change the lithium battery as described in the Technical Manual of the system board.

7.9System does not boot

System will not boot after installing a new SCSI hard disk drive.

SCSI configuration incorrect (standard SCSI controller)

ÊIn the SCSI configuration menu check the settings for the hard disk drives (SCSI Device Configuration ) and the settings under Advanced Configuration Options .

A26361-K646-Z102-1-7619

41

Image 49

Contents Primergy B120 Are there Page A26361-K646-Z102-1-7619 Operating Manual Primergy B120Page Contents Contents Introduction FeaturesSystem board Hard disk subsystemPower supply Introduction FeaturesService and Support High level of availability and failure protectionElectrical data standard power supply Technical dataNotational conventions IntroductionMechanical data StandardsEnvironmental conditions Noise levelInstallation and operation SafetyImportant notes Before operating the devicePoper operation of the system, warranty features Important notes SafetyBatteries Important notes CE certificateModules with electrostatic sensitive components Other important notesTransporting the server FCC Class B Compliance StatementEnvironmentally friendly product design and development Disposal and recyclingTake-back, recycling and disposal Further information on environmental protectionPage Installation steps InstallationUnpacking the server Setting up the tower server Instructions on connecting and disconnecting cablesInstallation Connecting cables125 240 Connecting the tower server to the line voltageConnecting the monitor to the line voltage Installing rack-server in/removing from rackMounting the slide-in module Installation Fitting spring nuts Installing the slide-in moduleMounting cage nuts Connecting the rack server to the line voltage Prepare the keyboard Installation Prepare the keyboardTower Rack Connecting devices to the serverConnecting devices to the server Preparation for use and operation Enabling access to the accessible drivesUnlocking/locking the tower server Preparation for use and operation Enabling access to the hard disk drivesOperation controls Drive indicators IndicatorsOperation controls Monitor screen Switching the server on and offServer is switched on Server is switched offOther switch-on methods Specified switch-on time/switch-off timeConfiguration with ServerStart Configuring the serverConfiguration without ServerStart Installing the operating systemFitting the hard disk cover Locking the tower serverLocking the server Cleaning the serverPage Opening and closing the tower server Opening and closing the serverOpening and closing the server Opening and closing the rack serverOpening and closing the rack server Page Property and data protection Page Operation indicator remains dark Troubleshooting and tipsServer switches itself off Screen stays blankFlickering stripes on the monitor screen Troubleshooting and tipsNo screen display or display drifts No mouse pointer displayed on the screen System does not bootFloppy disk cannot be read or written Time and/or date is not correctError messages on the screen Drives dead at system bootDisk Array Controller configuration is incorrect Added drive defectiveScsi hard disk subsystem System components and expansionsSystem components and expansions Scsi hard disk drivesRAID level 0 RAID level 1 and 5 without standby hard diskFunction of the indicators Green indicator Replacement of Scsi hard disk drive during operationOrange indicator Installing/removing a Scsi hard disk drive Scsi platter for four 1-inch hard disk slide-in modules IDE drive Accessible drivesScsi drive Open the server see Opening and closing the server Installing/Removing an accessible 5 ¼-inch driveChanging the floppy disk drive Removing/installing boards ChipDISK for RemoteView Installing/removing the chipDISKConfiguring the chipDISK Replacing the system fan System board Adapter modulePage ECC IndexKeyboard IndexSCSI-ID Troubleshooting and tips