Fujitsu B120 manual Installing/removing a Scsi hard disk drive

Page 54

System components and expansions

The SCSI hard disk subsystem

8.1.3 Installing/removing a SCSI hard disk drive

If a hard disk drive is to be installed in a bay in which no hard disk drive is previously installed, then the blind insert must be removed from this bay beforehand.

1

2

ÊSwivel the slide-in module handle of the hard disk slide-in module completely upward to release the locking mechanism (1) and pull the blank insert out of the installation by (2) by the handle.

The blank insert is installed in the reverse order.

Keep the blank insert for future use. If the hard disk drive is removed again and not ! replaced with a new drive, then the blank insert must be reinstalled due to cooling, the

applicable EMC regulations (regulations on electromagnetic compatibility) and fire protection.

2

1

ÊPush the hard disk carrier into the bay (1) as far as possible and then swing down the carrier handle completely to enable the locking mechanism to engage (2).

The removal of the hard disk carrier is performed in the reverse order.

46	A26361-K646-Z102-1-7619

Image 54

Contents Primergy B120 Are there Page A26361-K646-Z102-1-7619 Primergy B120 Operating ManualPage Contents Contents System board FeaturesIntroduction Hard disk subsystemService and Support Introduction FeaturesPower supply High level of availability and failure protectionNotational conventions Technical dataElectrical data standard power supply IntroductionEnvironmental conditions StandardsMechanical data Noise levelImportant notes SafetyInstallation and operation Before operating the deviceImportant notes Safety Poper operation of the system, warranty featuresBatteries Modules with electrostatic sensitive components CE certificateImportant notes Other important notesFCC Class B Compliance Statement Transporting the serverTake-back, recycling and disposal Disposal and recyclingEnvironmentally friendly product design and development Further information on environmental protectionPage Installation Installation stepsUnpacking the server Installation Instructions on connecting and disconnecting cablesSetting up the tower server Connecting cablesConnecting the tower server to the line voltage 125 240Installing rack-server in/removing from rack Connecting the monitor to the line voltageMounting the slide-in module Installation Installing the slide-in module Fitting spring nutsMounting cage nuts Connecting the rack server to the line voltage Installation Prepare the keyboard Prepare the keyboardConnecting devices to the server Tower RackConnecting devices to the server Enabling access to the accessible drives Preparation for use and operationUnlocking/locking the tower server Enabling access to the hard disk drives Preparation for use and operationOperation controls Indicators Drive indicatorsOperation controls Switching the server on and off Monitor screenOther switch-on methods Server is switched offServer is switched on Specified switch-on time/switch-off timeConfiguration without ServerStart Configuring the serverConfiguration with ServerStart Installing the operating systemLocking the tower server Fitting the hard disk coverCleaning the server Locking the serverPage Opening and closing the server Opening and closing the tower serverOpening and closing the rack server Opening and closing the serverOpening and closing the rack server Page Property and data protection Page Server switches itself off Troubleshooting and tipsOperation indicator remains dark Screen stays blankTroubleshooting and tips Flickering stripes on the monitor screenNo screen display or display drifts Floppy disk cannot be read or written System does not bootNo mouse pointer displayed on the screen Time and/or date is not correctDisk Array Controller configuration is incorrect Drives dead at system bootError messages on the screen Added drive defectiveSystem components and expansions Scsi hard disk subsystemRAID level 0 Scsi hard disk drivesSystem components and expansions RAID level 1 and 5 without standby hard diskReplacement of Scsi hard disk drive during operation Function of the indicators Green indicatorOrange indicator Installing/removing a Scsi hard disk drive Scsi platter for four 1-inch hard disk slide-in modules Accessible drives IDE driveScsi drive Installing/Removing an accessible 5 ¼-inch drive Open the server see Opening and closing the serverChanging the floppy disk drive Removing/installing boards Installing/removing the chipDISK ChipDISK for RemoteViewConfiguring the chipDISK Replacing the system fan Adapter module System boardPage Index ECCIndex KeyboardSCSI-ID Troubleshooting and tips