Fujitsu B120 manual ChipDISK for RemoteView, Installing/removing the chipDISK

Page 60

System components and expansions

chipDISK for RemoteView

8.4chipDISK for RemoteView

To use RemoteView, the remote test and diagnosis system, on the server, a RemoteView chipDISK is available for the PRIMERGY B120 server as an option. The RemoteView chipDISK is equipped with an IDE interface and is mounted in the server on the side of the drive cage on two spacer sleeves.

8.4.1 Installing/removing the chipDISK

ÊExit the operating system, switch off the server and disconnect it from the power supply.

	!	Switching off the server does not disconnect the device from the network. To completely
	!	disconnect the device from the network, remove the power plug from the line voltage.

Ê Open the server, and remove the side cover and the slot cover (see the chapter "Opening and closing the server").

1

M S C

2

3

ÊConnect the plug of the IDE ribbon cable to the IDE connection (2) and the small plug of the power supply cable to the power supply connection (3) of the chipDISK board.

!

Make sure the jumper (1) is set to M.

ÊOpen the server (see "Opening and closing the server").

52	A26361-K646-Z102-1-7619

Image 60

Contents Primergy B120 Are there Page A26361-K646-Z102-1-7619 Primergy B120 Operating ManualPage Contents Contents Features IntroductionSystem board Hard disk subsystemIntroduction Features Power supplyService and Support High level of availability and failure protectionTechnical data Electrical data standard power supplyNotational conventions IntroductionStandards Mechanical dataEnvironmental conditions Noise levelSafety Installation and operationImportant notes Before operating the deviceImportant notes Safety Poper operation of the system, warranty featuresBatteries CE certificate Important notesModules with electrostatic sensitive components Other important notesFCC Class B Compliance Statement Transporting the serverDisposal and recycling Environmentally friendly product design and developmentTake-back, recycling and disposal Further information on environmental protectionPage Installation Installation stepsUnpacking the server Instructions on connecting and disconnecting cables Setting up the tower serverInstallation Connecting cablesConnecting the tower server to the line voltage 125 240Installing rack-server in/removing from rack Connecting the monitor to the line voltageMounting the slide-in module Installation Installing the slide-in module Fitting spring nutsMounting cage nuts Connecting the rack server to the line voltage Installation Prepare the keyboard Prepare the keyboardConnecting devices to the server Tower RackConnecting devices to the server Enabling access to the accessible drives Preparation for use and operationUnlocking/locking the tower server Enabling access to the hard disk drives Preparation for use and operationOperation controls Indicators Drive indicatorsOperation controls Switching the server on and off Monitor screenServer is switched off Server is switched onOther switch-on methods Specified switch-on time/switch-off timeConfiguring the server Configuration with ServerStartConfiguration without ServerStart Installing the operating systemLocking the tower server Fitting the hard disk coverCleaning the server Locking the serverPage Opening and closing the server Opening and closing the tower serverOpening and closing the rack server Opening and closing the serverOpening and closing the rack server Page Property and data protection Page Troubleshooting and tips Operation indicator remains darkServer switches itself off Screen stays blankTroubleshooting and tips Flickering stripes on the monitor screenNo screen display or display drifts System does not boot No mouse pointer displayed on the screenFloppy disk cannot be read or written Time and/or date is not correctDrives dead at system boot Error messages on the screenDisk Array Controller configuration is incorrect Added drive defectiveSystem components and expansions Scsi hard disk subsystemScsi hard disk drives System components and expansionsRAID level 0 RAID level 1 and 5 without standby hard diskReplacement of Scsi hard disk drive during operation Function of the indicators Green indicatorOrange indicator Installing/removing a Scsi hard disk drive Scsi platter for four 1-inch hard disk slide-in modules Accessible drives IDE driveScsi drive Installing/Removing an accessible 5 ¼-inch drive Open the server see Opening and closing the serverChanging the floppy disk drive Removing/installing boards Installing/removing the chipDISK ChipDISK for RemoteViewConfiguring the chipDISK Replacing the system fan Adapter module System boardPage Index ECCIndex KeyboardSCSI-ID Troubleshooting and tips