Fujitsu B120 manual Scsi-Id

Page 67

Index

Opening 33
Operating system
installing			29
not starting				41
Operation		23
Overview
features			1
ports and slots					21
P
Packing material				9, 11
Parallel port 21
PDA technology				2
Plastic casing parts, Label;							9
Poper operation of the system								6
Ports	21
Power-on indicator					26
doesn't fail to light 39
Preparation for use					23
Processor, upgrading						55
Property protection					37
Protection, theft				37
R
Rack server
connecting				21
connectors				21
installing			14
opening and closing							34
RAID level		2, 43
Ready-to-operate 28
Recycling		9
RemoteView			52
Removing, hard disk cover							24
Ring indicator			28
S
Safety	5
board		7
SCA interface			1, 43
Screen
flickering			40
remains blank					39
SCSI drive		48
SCSI hard disk drive						43
hot-replacing 45
installing			46
removing			46
SCSI ID
accessible drive						48
SCSI platter, hot-replace 47
SCSI hard disk subsystem							43
SCSI platter, 4 x 1-inch carriers								47
SCSI-ID

hard disk drive						29, 43
SCU	29
Security measures						37
Security standards						4
Serial port			21
Server
opening				33
switches itself off							39
Server management						2
ServerStart			2, 29
ServerView			2
Setting up
tower server					12
Side cover
removing				33
Slide-in module
installing				17
mounting				15
Spring nut, fitting					17
Standard power supply							13, 19
Standards			4
Stand-by state				28
Streamer
installing				49
removing				49
Summer time				41
Switch	25
Switching off, server						27
Switching on, server						27
Symbols
explanation of						3
ports		21
System board				1
extensions					55
System components and expansions								43
System fan control						55
System fan, exchanging							54
T
Technical data				3
Temperature 4
Terminating resistor, accessible drive								48
Termination			48
Test and Diagnosis System 52
Time
not correct					41
Top cover, removing						34
Tower server
locking			23, 30
opening and closing 33
setting up				12
unlocking				23
Transport		8
Trouble
drive defect					42

A26361-K646-Z102-1-7619

59

Image 67

Contents Primergy B120 Are there Page A26361-K646-Z102-1-7619 Operating Manual Primergy B120Page Contents Contents Hard disk subsystem FeaturesIntroduction System boardHigh level of availability and failure protection Introduction FeaturesPower supply Service and SupportIntroduction Technical dataElectrical data standard power supply Notational conventionsNoise level StandardsMechanical data Environmental conditionsBefore operating the device SafetyInstallation and operation Important notesPoper operation of the system, warranty features Important notes SafetyBatteries Other important notes CE certificateImportant notes Modules with electrostatic sensitive componentsTransporting the server FCC Class B Compliance StatementFurther information on environmental protection Disposal and recyclingEnvironmentally friendly product design and development Take-back, recycling and disposalPage Installation steps InstallationUnpacking the server Connecting cables Instructions on connecting and disconnecting cablesSetting up the tower server Installation125 240 Connecting the tower server to the line voltageConnecting the monitor to the line voltage Installing rack-server in/removing from rackMounting the slide-in module Installation Fitting spring nuts Installing the slide-in moduleMounting cage nuts Connecting the rack server to the line voltage Prepare the keyboard Installation Prepare the keyboardTower Rack Connecting devices to the serverConnecting devices to the server Preparation for use and operation Enabling access to the accessible drivesUnlocking/locking the tower server Preparation for use and operation Enabling access to the hard disk drivesOperation controls Drive indicators IndicatorsOperation controls Monitor screen Switching the server on and offSpecified switch-on time/switch-off time Server is switched offServer is switched on Other switch-on methodsInstalling the operating system Configuring the serverConfiguration with ServerStart Configuration without ServerStartFitting the hard disk cover Locking the tower serverLocking the server Cleaning the serverPage Opening and closing the tower server Opening and closing the serverOpening and closing the server Opening and closing the rack serverOpening and closing the rack server Page Property and data protection Page Screen stays blank Troubleshooting and tipsOperation indicator remains dark Server switches itself offFlickering stripes on the monitor screen Troubleshooting and tipsNo screen display or display drifts Time and/or date is not correct System does not bootNo mouse pointer displayed on the screen Floppy disk cannot be read or writtenAdded drive defective Drives dead at system bootError messages on the screen Disk Array Controller configuration is incorrectScsi hard disk subsystem System components and expansionsRAID level 1 and 5 without standby hard disk Scsi hard disk drivesSystem components and expansions RAID level 0Function of the indicators Green indicator Replacement of Scsi hard disk drive during operationOrange indicator Installing/removing a Scsi hard disk drive Scsi platter for four 1-inch hard disk slide-in modules IDE drive Accessible drivesScsi drive Open the server see Opening and closing the server Installing/Removing an accessible 5 ¼-inch driveChanging the floppy disk drive Removing/installing boards ChipDISK for RemoteView Installing/removing the chipDISKConfiguring the chipDISK Replacing the system fan System board Adapter modulePage ECC IndexKeyboard IndexSCSI-ID Troubleshooting and tips