Fujitsu B120 manual Installing/Removing an accessible 5 ¼-inch drive

Page 57

Accessible drives

System components and expansions

8.2.1 Installing/Removing an accessible 5 ¼-inch drive

ÊShut down the operating system.

ÊSwitch off the server, and disconnect it from the network.

	!	Switching off the server does not disconnect the device from the network. To completely
	!	disconnect the device from the network, remove the power plug from the line voltage.

Ê Open the server (see "Opening and closing the server").

3

2

1

ÊDisconnect the cables from the drive (1).

ÊRemove the two fastening screws (2) and take out the drive toward the front (3). The new drive is mounted in reverse order.

If you do not install a new drive, proceed as follows:

1	2
a	2
	b

ÊMount an EMC insert (a) and a plastic cover (b) in the empty bay (1 + 2).

ÊClose the server again (see "Opening and closing the server").

A26361-K646-Z102-1-7619

49

Image 57

Contents Primergy B120 Are there Page A26361-K646-Z102-1-7619 Operating Manual Primergy B120Page Contents Contents Introduction FeaturesSystem board Hard disk subsystemPower supply Introduction FeaturesService and Support High level of availability and failure protectionElectrical data standard power supply Technical dataNotational conventions IntroductionMechanical data StandardsEnvironmental conditions Noise levelInstallation and operation SafetyImportant notes Before operating the deviceImportant notes Safety Poper operation of the system, warranty featuresBatteries Important notes CE certificateModules with electrostatic sensitive components Other important notesTransporting the server FCC Class B Compliance StatementEnvironmentally friendly product design and development Disposal and recyclingTake-back, recycling and disposal Further information on environmental protectionPage Installation Installation stepsUnpacking the server Setting up the tower server Instructions on connecting and disconnecting cablesInstallation Connecting cables125 240 Connecting the tower server to the line voltageConnecting the monitor to the line voltage Installing rack-server in/removing from rackMounting the slide-in module Installation Fitting spring nuts Installing the slide-in moduleMounting cage nuts Connecting the rack server to the line voltage Prepare the keyboard Installation Prepare the keyboardTower Rack Connecting devices to the serverConnecting devices to the server Enabling access to the accessible drives Preparation for use and operationUnlocking/locking the tower server Preparation for use and operation Enabling access to the hard disk drivesOperation controls Indicators Drive indicatorsOperation controls Monitor screen Switching the server on and offServer is switched on Server is switched offOther switch-on methods Specified switch-on time/switch-off timeConfiguration with ServerStart Configuring the serverConfiguration without ServerStart Installing the operating systemFitting the hard disk cover Locking the tower serverLocking the server Cleaning the serverPage Opening and closing the tower server Opening and closing the serverOpening and closing the server Opening and closing the rack serverOpening and closing the rack server Page Property and data protection Page Operation indicator remains dark Troubleshooting and tipsServer switches itself off Screen stays blankTroubleshooting and tips Flickering stripes on the monitor screenNo screen display or display drifts No mouse pointer displayed on the screen System does not bootFloppy disk cannot be read or written Time and/or date is not correctError messages on the screen Drives dead at system bootDisk Array Controller configuration is incorrect Added drive defectiveScsi hard disk subsystem System components and expansionsSystem components and expansions Scsi hard disk drivesRAID level 0 RAID level 1 and 5 without standby hard diskReplacement of Scsi hard disk drive during operation Function of the indicators Green indicatorOrange indicator Installing/removing a Scsi hard disk drive Scsi platter for four 1-inch hard disk slide-in modules Accessible drives IDE driveScsi drive Open the server see Opening and closing the server Installing/Removing an accessible 5 ¼-inch driveChanging the floppy disk drive Removing/installing boards ChipDISK for RemoteView Installing/removing the chipDISKConfiguring the chipDISK Replacing the system fan System board Adapter modulePage ECC IndexKeyboard IndexSCSI-ID Troubleshooting and tips