Fujitsu B120 manual Contents

Page 8

Contents

7.8	Time and/or date is not correct	41
7.9	System does not boot	41
7.10 Drives "dead" at system boot		42
7.11 Added drive defective		42
7.12 Error messages on the screen		42
8 System components and expansions		43
8.1	The SCSI hard disk subsystem	43
8.1.1 SCSI hard disk drives		44
8.1.2 Replacement of SCSI hard disk drive during operation		45
8.1.3 Installing/removing a SCSI hard disk drive		46
8.1.4 SCSI platter for four 1-inch hard disk slide-in modules		47
8.2	Accessible drives	48
8.2.1 Installing/Removing an accessible 5 ¼-inch drive		49
8.2.2 Changing the floppy disk drive		50
8.3	Removing/installing boards	51
8.4 chipDISK for RemoteView		52
8.4.1 Installing/removing the chipDISK		52
8.4.2 Configuring the chipDISK		53
8.5	Replacing the system fan	54
8.6	Adapter module	55
8.7	System board	55
9 Index		57

A26361-K646-Z102-1-7619

Image 8

Contents Primergy B120 Are there Page A26361-K646-Z102-1-7619 Primergy B120 Operating ManualPage Contents Contents Features IntroductionSystem board Hard disk subsystemIntroduction Features Power supplyService and Support High level of availability and failure protectionTechnical data Electrical data standard power supplyNotational conventions IntroductionStandards Mechanical dataEnvironmental conditions Noise levelSafety Installation and operationImportant notes Before operating the deviceBatteries Important notes SafetyPoper operation of the system, warranty features CE certificate Important notesModules with electrostatic sensitive components Other important notesFCC Class B Compliance Statement Transporting the serverDisposal and recycling Environmentally friendly product design and developmentTake-back, recycling and disposal Further information on environmental protectionPage Unpacking the server InstallationInstallation steps Instructions on connecting and disconnecting cables Setting up the tower serverInstallation Connecting cablesConnecting the tower server to the line voltage 125 240Installing rack-server in/removing from rack Connecting the monitor to the line voltageMounting the slide-in module Installation Installing the slide-in module Fitting spring nutsMounting cage nuts Connecting the rack server to the line voltage Installation Prepare the keyboard Prepare the keyboardConnecting devices to the server Tower RackConnecting devices to the server Unlocking/locking the tower server Enabling access to the accessible drivesPreparation for use and operation Enabling access to the hard disk drives Preparation for use and operationOperation controls Operation controls IndicatorsDrive indicators Switching the server on and off Monitor screenServer is switched off Server is switched onOther switch-on methods Specified switch-on time/switch-off timeConfiguring the server Configuration with ServerStartConfiguration without ServerStart Installing the operating systemLocking the tower server Fitting the hard disk coverCleaning the server Locking the serverPage Opening and closing the server Opening and closing the tower serverOpening and closing the rack server Opening and closing the serverOpening and closing the rack server Page Property and data protection Page Troubleshooting and tips Operation indicator remains darkServer switches itself off Screen stays blankNo screen display or display drifts Troubleshooting and tipsFlickering stripes on the monitor screen System does not boot No mouse pointer displayed on the screenFloppy disk cannot be read or written Time and/or date is not correctDrives dead at system boot Error messages on the screenDisk Array Controller configuration is incorrect Added drive defectiveSystem components and expansions Scsi hard disk subsystemScsi hard disk drives System components and expansionsRAID level 0 RAID level 1 and 5 without standby hard diskOrange indicator Replacement of Scsi hard disk drive during operationFunction of the indicators Green indicator Installing/removing a Scsi hard disk drive Scsi platter for four 1-inch hard disk slide-in modules Scsi drive Accessible drivesIDE drive Installing/Removing an accessible 5 ¼-inch drive Open the server see Opening and closing the serverChanging the floppy disk drive Removing/installing boards Installing/removing the chipDISK ChipDISK for RemoteViewConfiguring the chipDISK Replacing the system fan Adapter module System boardPage Index ECCIndex KeyboardSCSI-ID Troubleshooting and tips