Fujitsu RX330 manual Controls and displays, Indicators on the control panel

Page 50

Controls and displays

Starting up and operation

Controls

On/Off button

When the system is switched off, it can be switched on again by pressing the On/Off button. When the system is operating, pressing the On/Off button will switch off the system.

IThe On/Off button does not disconnect the server from the mains. To disconnect from the mains completely, remove the power plug(s).

NMI NMI button

IDo not press! The NMI button may only be used by service personnel.

RST Reset button

Pressing the reset button reboots the system.

ID ID button

Lights up (blue) on the front and on the rear of the server when the ID button is pressed. The two ID indicators are synchronized.

Indicators on the control panel

Power-on indicator (three colors)

Lights red when the server is switched off but line voltage is present.

Lights yellow during power up delay.

IIf the server is switched off and then immediately switched on again, a server is only restarted after a power up delay. This prevents a current overload, for example.

You can set the power up delay (in seconds) in the BIOS setup in the Server Menu menu with Power Cycle Delay .

Lights up green when the server is switched ON.

Flashes green when the server has been switched on and is in standby mode.

50

Operating manual

RX330 S1

Image 50

Contents Primergy RX330 S1 Server Certified documentation according to DIN EN ISO Comments… Suggestions… Corrections…Copyright and Trademarks Contents Contents Abbreviations Literature Index Page Concept and target groups for this manual IntroductionDocumentation overview Documentation overview Additional server documentationFurther sources of information FeaturesIntroduction System boardPower supply FeaturesAccessible drives USB portIRMC with integrated service LAN port Features Server management Service and support ServerStartRemoteView Notational conventions Notational conventionsCompliance with regulations and standards Technical dataElectrical data hot-plug power supply unit Mechanical values Technical dataWeight Ventilation clearanceInstallation steps, overview Installation steps, overview Safety Important informationBefore starting up SafetyInstallation and operation Important information Safety Never remove parts of the CD/DVD drive casing Working with CDs/DVDs and CD/DVD drivesLaser information Batteries Modules with Electrostatic-Sensitive Devices ESD labelCE conformity CE conformityFCC Class a Compliance Statement Other important informationTransporting the server Important information Energy-saving information Environmental protectionEnvironmentally-friendly product design and development Packaging informationReturns, recycling and disposal Environmental protectionLabels on plastic casing parts Hours Hardware installationMinimum acclimatization time Unpacking the server Unpacking the serverInstalling/removing the server in/from the rack Rack requirementsDataCenter Rack Installing/removing the server in/from the rackPrimecenter Rack Operating manual Mechanical requirements Installation in PRIMECENTER/DataCenter Rack Fitting the support bracketRemove the outer telescopic rail Operating manual Installation in 3rd party racks Racks with installation depth of 735 mmInserting the server Preparing the serverInserting the server Connecting devices to the server Hardware installationConnecting devices to the server Connecting the keyboard, mouse and monitorConnecting the server to the mains Connecting the server to the mainsConnecting cables Disconnecting cablesFront of server Starting up and operationControls and displays Controls Indicators on the control panelControls and displays Indicators on the drives CD/DVD indicator Starting up and operationIndicators on the HDD module LEDGlobal error indicator and ID indicator Rear of serverIndicators on the connection panel LAN indicators LAN indicatorsHot-plug PSU indicators Status MeaningSwitching the server on Switching the server on and offSwitching the server on and off System already installedRing indicator Switching the server OFFSpecified switch on time / switch off time After power failureConfiguring the server Configuring the serverConfiguring onboard SAS controller Configuration with ServerStart ServerStart advantagesCleaning the server Cleaning the serverConfiguration without ServerStart Configuring onboard SAS controllerPreventing unauthorized system access Bios Setup security functionsPreventing unauthorized Bios Setup calls Property and data protectionProtecting Bios from being overwritten Protecting the server from being switched off by a programPower cable incorrectly connected Troubleshooting and tipsPower-on indicator remains unlit Power supply overloadedServer switches itself off Screen remains blankNo mouse pointer displayed on screen Flickering stripes on monitor screenNo screen display or display drifts SAS configuration incorrect System will not bootMouse controller disabled Incorrect date and timeRAID controller configuration incorrect Drives reported as dead when starting systemError message on screen RAID controller is not configured for this drivePage Hot-plug power supply units Hot-plug componentsHot-plug power supply units Remove the dummy moduleInstalling/removing the hot-plug power supply unit Hot-plug componentsReplacing the hot-plug power supply unit Hot plug hard disk drives Hot plug hard disk drives HDD module and dummy moduleHandling hard disk drives and HDD modules Removing/Installing the dummy module Removing the dummy moduleInstalling/removing the HDD module Unlocking the HDD moduleInstalling the HDD module Installing the HDD moduleRemoving the HDD module Vcaution Abbreviations Abbreviations IRMC LBA RAM SEL Literature Primergy ServerView Suite Literature Primergy ServerView Suite ServerView S2Primergy ServerView Suite ServerView Index CD-RW DVD-RWIndex DVDUSB Dimensions Electrical data Index