Fujitsu RX330 Switching the server OFF, Other on/off options, Ring indicator, Wake On LAN WOL

Page 57

Starting up and operation

Switching the server on and off

Switching the server OFF

Power-on indicator (position 10 in figure 11 on page 49) lights green.

ÊShut down the operating system properly.

The server is automatically switched off. The Power-on indicator lights red.

IIf the operating system does not switch the server off automatically, press the On/Off button for at least four seconds and/or send a corre- sponding control signal.

Other on/off options

In addition to the On/Off button, the server can be switched ON and OFF in the following ways:

–Specified switch on time / switch off time

The server is switched ON or OFF at a time specified in the ServerView program

–Ring indicator

The server is switched on by an internal or external modem.

–Wake On LAN (WOL)

The server is switched on by a command via the LAN (Magic Packet).

–After power failure

The server automatically reboots following a power failure (depending of the settings in the BIOS).

–“Power override” function

The server can be switched off immediately by pressing and holding the On/Off button (approx. 4-5 sec.).

VCAUTION!

There is a risk that data may be lost.

RX330 S1

Operating manual

57

Image 57

Contents Primergy RX330 S1 Server Comments… Suggestions… Corrections… Copyright and TrademarksCertified documentation according to DIN EN ISO Contents Contents Abbreviations Literature Index Page Introduction Documentation overviewConcept and target groups for this manual Additional server documentation Documentation overviewIntroduction FeaturesFurther sources of information System boardAccessible drives FeaturesPower supply USB portIRMC with integrated service LAN port Features Server management ServerStart Service and supportRemoteView Notational conventions Notational conventionsTechnical data Electrical data hot-plug power supply unitCompliance with regulations and standards Weight Technical dataMechanical values Ventilation clearanceInstallation steps, overview Installation steps, overview Important information SafetySafety Installation and operationBefore starting up Important information Safety Working with CDs/DVDs and CD/DVD drives Laser informationNever remove parts of the CD/DVD drive casing Batteries ESD label Modules with Electrostatic-Sensitive DevicesFCC Class a Compliance Statement CE conformityCE conformity Other important informationTransporting the server Important information Environmentally-friendly product design and development Environmental protectionEnergy-saving information Packaging informationEnvironmental protection Labels on plastic casing partsReturns, recycling and disposal Hardware installation Minimum acclimatization timeHours Unpacking the server Unpacking the serverRack requirements Installing/removing the server in/from the rackInstalling/removing the server in/from the rack Primecenter RackDataCenter Rack Operating manual Mechanical requirements Fitting the support bracket Installation in PRIMECENTER/DataCenter RackRemove the outer telescopic rail Operating manual Racks with installation depth of 735 mm Installation in 3rd party racksPreparing the server Inserting the serverInserting the server Hardware installation Connecting devices to the serverConnecting the keyboard, mouse and monitor Connecting devices to the serverConnecting the server to the mains Connecting the server to the mainsDisconnecting cables Connecting cablesStarting up and operation Controls and displaysFront of server Indicators on the control panel Controls and displaysControls Starting up and operation Indicators on the drives CD/DVD indicatorLED Indicators on the HDD moduleRear of server Global error indicator and ID indicatorLAN indicators Indicators on the connection panel LAN indicatorsStatus Meaning Hot-plug PSU indicatorsSwitching the server on and off Switching the server on and offSwitching the server on System already installedSpecified switch on time / switch off time Switching the server OFFRing indicator After power failureConfiguring the server Configuring onboard SAS controllerConfiguring the server ServerStart advantages Configuration with ServerStartConfiguration without ServerStart Cleaning the serverCleaning the server Configuring onboard SAS controllerPreventing unauthorized Bios Setup calls Bios Setup security functionsPreventing unauthorized system access Property and data protectionProtecting the server from being switched off by a program Protecting Bios from being overwrittenPower-on indicator remains unlit Troubleshooting and tipsPower cable incorrectly connected Power supply overloadedScreen remains blank Server switches itself offFlickering stripes on monitor screen No screen display or display driftsNo mouse pointer displayed on screen Mouse controller disabled System will not bootSAS configuration incorrect Incorrect date and timeError message on screen Drives reported as dead when starting systemRAID controller configuration incorrect RAID controller is not configured for this drivePage Hot-plug components Hot-plug power supply unitsRemove the dummy module Hot-plug power supply unitsHot-plug components Installing/removing the hot-plug power supply unitReplacing the hot-plug power supply unit Hot plug hard disk drives HDD module and dummy module Hot plug hard disk drivesHandling hard disk drives and HDD modules Removing the dummy module Removing/Installing the dummy moduleUnlocking the HDD module Installing/removing the HDD moduleInstalling the HDD module Installing the HDD moduleRemoving the HDD module Vcaution Abbreviations Abbreviations IRMC LBA RAM SEL Literature Literature Primergy ServerView Suite ServerView S2 Primergy ServerView Suite ServerViewPrimergy ServerView Suite CD-RW DVD-RW IndexDVD IndexUSB Dimensions Electrical data Index