Fujitsu RX330 manual Incorrect date and time, System will not boot, Mouse controller disabled

Page 66

Incorrect date and time

Troubleshooting and tips

Mouse controller disabled

The mouse controller on the system board must be enabled if you are using the mouse supplied.

ÊCheck in the BIOS Setup that the mouse controller is Enabled.

7.7Incorrect date and time

ÊSet the date and time in the operating system or in the BIOS Setup under the Main menu, using System Date and System Time respectively.

INote that the operating system may affect the system time. For example, the operating system time may deviate from the system time under Linux, and would overwrite the system time in the default setting on shutdown.

If the date and time are still wrong after the server has been switched off and back on again, replace the lithium battery (for a description refer to the Technical Manual for the D2440 system board) or contact our customer service team.

7.8System will not boot

The system will not boot after installing a new hard disk drive.

SAS configuration incorrect

ÊCheck the settings for the hard disk drives (SAS Device Configuration) and the additional settings in the SAS configuration menu.

66

Operating manual

RX330 S1

Image 66

Contents Primergy RX330 S1 Server Comments… Suggestions… Corrections… Copyright and TrademarksCertified documentation according to DIN EN ISO Contents Contents Abbreviations Literature Index Page Introduction Documentation overviewConcept and target groups for this manual Documentation overview Additional server documentationFurther sources of information FeaturesIntroduction System boardPower supply FeaturesAccessible drives USB portIRMC with integrated service LAN port Features Server management Service and support ServerStartRemoteView Notational conventions Notational conventionsTechnical data Electrical data hot-plug power supply unitCompliance with regulations and standards Mechanical values Technical dataWeight Ventilation clearanceInstallation steps, overview Installation steps, overview Safety Important informationSafety Installation and operationBefore starting up Important information Safety Working with CDs/DVDs and CD/DVD drives Laser informationNever remove parts of the CD/DVD drive casing Batteries Modules with Electrostatic-Sensitive Devices ESD labelCE conformity CE conformityFCC Class a Compliance Statement Other important informationTransporting the server Important information Energy-saving information Environmental protectionEnvironmentally-friendly product design and development Packaging informationEnvironmental protection Labels on plastic casing partsReturns, recycling and disposal Hardware installation Minimum acclimatization timeHours Unpacking the server Unpacking the serverInstalling/removing the server in/from the rack Rack requirementsInstalling/removing the server in/from the rack Primecenter RackDataCenter Rack Operating manual Mechanical requirements Installation in PRIMECENTER/DataCenter Rack Fitting the support bracketRemove the outer telescopic rail Operating manual Installation in 3rd party racks Racks with installation depth of 735 mmInserting the server Preparing the serverInserting the server Connecting devices to the server Hardware installationConnecting devices to the server Connecting the keyboard, mouse and monitorConnecting the server to the mains Connecting the server to the mainsConnecting cables Disconnecting cablesStarting up and operation Controls and displaysFront of server Indicators on the control panel Controls and displaysControls Indicators on the drives CD/DVD indicator Starting up and operationIndicators on the HDD module LEDGlobal error indicator and ID indicator Rear of serverIndicators on the connection panel LAN indicators LAN indicatorsHot-plug PSU indicators Status MeaningSwitching the server on Switching the server on and offSwitching the server on and off System already installedRing indicator Switching the server OFFSpecified switch on time / switch off time After power failureConfiguring the server Configuring onboard SAS controllerConfiguring the server Configuration with ServerStart ServerStart advantagesCleaning the server Cleaning the serverConfiguration without ServerStart Configuring onboard SAS controllerPreventing unauthorized system access Bios Setup security functionsPreventing unauthorized Bios Setup calls Property and data protectionProtecting Bios from being overwritten Protecting the server from being switched off by a programPower cable incorrectly connected Troubleshooting and tipsPower-on indicator remains unlit Power supply overloadedServer switches itself off Screen remains blankFlickering stripes on monitor screen No screen display or display driftsNo mouse pointer displayed on screen SAS configuration incorrect System will not bootMouse controller disabled Incorrect date and timeRAID controller configuration incorrect Drives reported as dead when starting systemError message on screen RAID controller is not configured for this drivePage Hot-plug power supply units Hot-plug componentsHot-plug power supply units Remove the dummy moduleInstalling/removing the hot-plug power supply unit Hot-plug componentsReplacing the hot-plug power supply unit Hot plug hard disk drives Hot plug hard disk drives HDD module and dummy moduleHandling hard disk drives and HDD modules Removing/Installing the dummy module Removing the dummy moduleInstalling/removing the HDD module Unlocking the HDD moduleInstalling the HDD module Installing the HDD moduleRemoving the HDD module Vcaution Abbreviations Abbreviations IRMC LBA RAM SEL Literature Literature Primergy ServerView Suite ServerView S2 Primergy ServerView Suite ServerViewPrimergy ServerView Suite Index CD-RW DVD-RWIndex DVDUSB Dimensions Electrical data Index