Cisco Systems 100/200/300/400 Running the Bios Setup Utility, Ethernet Stream, Interface Ports

Page 54

Chapter 4 Installing the Internet Streamer CDS Software and Initially Configuring a CDE

Running the BIOS Setup Utility

Note For the CDE100, use the internal CD-ROM drive for recovery or remanufacture procedures.

For the CDE200, do not use the internal CD-ROM drive for recovery or remanufacture procedures. Use the external USB CD-ROM drive for all procedures that require a CD-ROM drive.

You also need to configure the ports on the CDE200 as shown below:

•The two built-in Gigabit Ethernet ports are GigabitEthernet 1/0 and GigabitEthernet 2/0 and are management ports using channel bonding 1 (see Figure 1-18).

Ethernet Management	Gigabit Ethernet
Ports	Management Ports

eth0	g1/0

eth1	g2/0

•The four interface ports on the stream interfaces are GigabitEthernet 3/0, GigabitEthernet 4/0, GigabitEthernet 5/0 and GigabitEthernet 6/0 using channel bonding 2 (see Figure 1-18).

Ethernet Stream	Gigabit Ethernet Stream
Interface Ports	Interface Ports

eth2	g3/0

eth3	g4/0

eth4	g5/0

eth5	g6/0

Installation and Configuration Order

Perform the initial installation and configuration of your CDS network in the following order:

1.Run the BIOS setup utility on each CDE in the CDS network.

2.Install the CDS Release 2.0-2.1 software on each CDE in the CDS network.

3.Configure the CDSM.

Caution It is very important that the onboard SCSI controller be disabled on the CDE200. Do this by physically opening the CDE200 case (by removing two side screws and a back thumbscrew), and verifying that the jumper labeled “JPA-1” (located about two inches below the center PCI-X slot—slot 3 of 5) has pins 2 and 3 connected (instead of 1 and 2). Pin 1 is closest to the rear of the case and pin 3 is closest to the front.

Running the BIOS Setup Utility

Running the BIOS setup utility is different for the CDE100 and the CDE200; therefore, this section provides a separate BIOS setup procedure for each CDE.

Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide

4-2	OL-13478-03

Image 54

Contents March Americas HeadquartersCisco Systems, Inc. All rights reserved N T E N T S Connecting Network Cables Ethernet Connector Pin Assignments B-2 OL-13478-03 Document Revision History Document OrganizationDate Change Summary Related Documentation ObjectivesAudience Chapter DescriptionConventions Safety Information Referral Warning Cisco Internet Streamer CDS 2.x Product DocumentationWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaTA Vare PÅ Disse Instruksjonene Aviso Instruções Importantes DE SegurançaXii GEM Disse Anvisninger Xiv Obtaining Documentation and Submitting a Service Request Xvi Overview of the Content Delivery Engines Cisco Internet Streamer CDS OverviewCisco TV CDS Overview OnDemand ApplicationVideo Accelerator Software Hardware Features CDE200 Front ViewEth5 eth3 Rack Unit Ethernet Processor Memory DrivesInterface Control Buttons Processor Memory Drives GE Ports Interface10 CDE200 Front Panel Control Buttons LED Indicators 12 CDE400 Back Panel Control ButtonsLED Color State Description15 CDE300 Front Panel LEDs Input/Output Ports and Connectors 17 CDE100 Connector LocationsCDE200 Connector Locations CDE400 Connector Locations OL-13478-03 Site Requirements Preventing Electrostatic Discharge DamageEnvironmental, Physical, and Power Specifications Safety Warnings OL-13478-03 Page DC Power Option Warnings Safety GuidelinesAC Power Option Warnings General PrecautionsProtecting Against Electrostatic Discharge Emissions Disclaimer Safety InformationIf AC Power Supplies Are Installed Intended UsesIf DC Power Supplies Are Installed Amps StatementTemperature and Ventilation Installing the Content Delivery Engines Server TypesTools and Parts Required Unpacking the BoxVerifying Contents Installing the CDEsInspecting for Damage Preparing the CDEs for Rack Installation Installing CDEs in the Rack Making Physical ConnectionsConnecting Power Cords CDE300 SX Version Connector Locations Connecting Network Cables Installing or Removing Disk Drives Interface Switch Port MbpsCDE400 Disk Drive Locations Statement 11 Disk Drive Tray Installation and Removal Before You Begin Ethernet Management Gigabit Ethernet Ports Management Ports Running the Bios Setup UtilityInstallation and Configuration Order Ethernet StreamRunning the Bios Setup Utility for the CDE100 Boot Settings Menu Boot Device Priority Screen Advanced Settings Menu Set the Serial Port2 Address option to Disabled 10 Exit Options Screen Running the Bios Setup Utility for the CDE200 Set the QuickBoot Mode option to Enabled 14 Hard Disk Drives Screen Set the Com Port Address option to On-board COM a Installing the Software Model CDE200Initially Configuring a CDE Assigning the Primary InterfaceRunning the Setup Utility Verifying the Cdsm18 Cdsm Login Documentation section on OL-13478-03 Hardware Troubleshooting Troubleshooting Ethernet AdaptersTroubleshooting Sata Drives Technical Specifications SpecificationsCDE100 CDE200CDE300 CDE400Management Data RateInput Cables Serial Console Interface Connector Pin Assignments Description PinEthernet Connector Pin Assignments Serial Port ConnectorEthernet Port Connector Pin T568B 100BASE-T SignalRJ-45 Pin End Wire Color Diagram End Cable Pin Assignments ComputerWhite/Orange White/Green Blue White/Blue White/Brown OL-13478-03 Management Interface WeightFan Assembly ProcessorStream Interfaces Content Storage CapacityIngest Interface TransportCached Content Capacity CDE200 IBMEthernet Interfaces Scsi Controllers Connector Pin Assignments Figure C-1shows the location of all connectors for a CDE100Figure C-3 CDE200 IBM Connector Locations Eth1 Eth0 Eth3 eth5 Eth6 Eth5 Eth8 Eth2 Eth4 Eth7 Eth1 Eth3 Connecting DC Power DC Power OverviewConnecting DC Power to a CDE200 Figure D-2 CDE200 Rear PanelStar washer PM ground ring lug Nut Disconnecting Power and Replacing a PM on a CDE200 Connecting DC Power to a CDE200 section on page D-2Connecting DC Power to a CDE300 Figure D-5 CDE300 Rear PanelFigure D-6 CDE300 Building/PM Ground Stud Order Connecting DC Power to a CDE400 Disconnecting Power and Replacing a PM on a CDE30048 VDC Figure D-8 CDE400 PM Ground Stud Order Disconnecting Power and Replacing a PM on a CDE400 DC Power Cable Connector and Pinouts OL-13478-03 Numerics IN-2 IN-3 IN-4 IN-5 IN-6