Cisco Systems 100/200/300/400 specifications Hard Disk Drives Screen

Page 63

Chapter 4 Installing the Internet Streamer CDS Software and Initially Configuring a CDE

Running the BIOS Setup Utility

Figure 4-14 Hard Disk Drives Screen

Step 9 Use the on-screen instructions to move the elements into the following order:

1.CD-ROM drive (first boot device)

2.Flash device (first hard drive)

3.Removable devices

4.Network device

Caution The devices must be in the correct order for the installation to be successful.

Step 10 Press Esc to return to the Main menu. To configure IDE, set the IDE Channel 0 Master option to None and the IDE Channel 1 Master option to 128 (this is compact flash card) (see Figure 4-15).

Figure 4-15

Main Menu

Note On the CDE200, the Primary IDE Master is connected to the 80-GB hard drive (not used), and the Secondary IDE Master is connected to a 128-MB compact flash drive.

 

 

Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide

 

 

 

 

 

 

OL-13478-03

 

 

4-11

 

 

 

 

 

Image 63
Contents Americas Headquarters MarchCisco Systems, Inc. All rights reserved N T E N T S Connecting Network Cables Ethernet Connector Pin Assignments B-2 OL-13478-03 Document Revision History Document OrganizationDate Change Summary Chapter Description ObjectivesAudience Related DocumentationCisco Internet Streamer CDS 2.x Product Documentation Conventions Safety Information Referral WarningAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseAviso Instruções Importantes DE Segurança TA Vare PÅ Disse InstruksjoneneXii GEM Disse Anvisninger Xiv Obtaining Documentation and Submitting a Service Request Xvi Cisco Internet Streamer CDS Overview Overview of the Content Delivery EnginesCisco TV CDS Overview OnDemand ApplicationVideo Accelerator Software CDE200 Front View Hardware FeaturesEth5 eth3 Rack Unit Ethernet Processor Memory DrivesInterface Processor Memory Drives GE Ports Interface Control Buttons10 CDE200 Front Panel Control Buttons 12 CDE400 Back Panel Control Buttons LED IndicatorsColor State Description LED15 CDE300 Front Panel LEDs 17 CDE100 Connector Locations Input/Output Ports and ConnectorsCDE200 Connector Locations CDE400 Connector Locations OL-13478-03 Preventing Electrostatic Discharge Damage Site RequirementsEnvironmental, Physical, and Power Specifications Safety Warnings OL-13478-03 Page General Precautions Safety GuidelinesAC Power Option Warnings DC Power Option WarningsProtecting Against Electrostatic Discharge Intended Uses Safety InformationIf AC Power Supplies Are Installed Emissions DisclaimerAmps Statement If DC Power Supplies Are InstalledTemperature and Ventilation Server Types Installing the Content Delivery EnginesUnpacking the Box Tools and Parts RequiredVerifying Contents Installing the CDEsInspecting for Damage Preparing the CDEs for Rack Installation Making Physical Connections Installing CDEs in the RackConnecting Power Cords CDE300 SX Version Connector Locations Connecting Network Cables Interface Switch Port Mbps Installing or Removing Disk DrivesCDE400 Disk Drive Locations Statement 11 Disk Drive Tray Installation and Removal Before You Begin Ethernet Stream Running the Bios Setup UtilityInstallation and Configuration Order Ethernet Management Gigabit Ethernet Ports Management PortsRunning the Bios Setup Utility for the CDE100 Boot Settings Menu Boot Device Priority Screen Advanced Settings Menu Set the Serial Port2 Address option to Disabled 10 Exit Options Screen Running the Bios Setup Utility for the CDE200 Set the QuickBoot Mode option to Enabled 14 Hard Disk Drives Screen Set the Com Port Address option to On-board COM a Model CDE200 Installing the SoftwareAssigning the Primary Interface Initially Configuring a CDEVerifying the Cdsm Running the Setup Utility18 Cdsm Login Documentation section on OL-13478-03 Troubleshooting Ethernet Adapters Hardware TroubleshootingTroubleshooting Sata Drives Specifications Technical SpecificationsCDE200 CDE100CDE400 CDE300Management Data RateInput Cables Description Pin Serial Console Interface Connector Pin AssignmentsSerial Port Connector Ethernet Connector Pin AssignmentsEthernet Port Connector Pin T568B 100BASE-T SignalRJ-45 Pin End Wire Color Diagram End Computer Cable Pin AssignmentsWhite/Orange White/Green Blue White/Blue White/Brown OL-13478-03 Processor WeightFan Assembly Management InterfaceTransport Content Storage CapacityIngest Interface Stream InterfacesCached Content Capacity CDE200 IBMEthernet Interfaces Scsi Controllers Figure C-1shows the location of all connectors for a CDE100 Connector Pin AssignmentsFigure C-3 CDE200 IBM Connector Locations Eth1 Eth0 Eth3 eth5 Eth6 Eth5 Eth8 Eth2 Eth4 Eth7 Eth1 Eth3 DC Power Overview Connecting DC PowerFigure D-2 CDE200 Rear Panel Connecting DC Power to a CDE200Star washer PM ground ring lug Nut Connecting DC Power to a CDE200 section on page D-2 Disconnecting Power and Replacing a PM on a CDE200Figure D-5 CDE300 Rear Panel Connecting DC Power to a CDE300Figure D-6 CDE300 Building/PM Ground Stud Order Disconnecting Power and Replacing a PM on a CDE300 Connecting DC Power to a CDE40048 VDC Figure D-8 CDE400 PM Ground Stud Order Disconnecting Power and Replacing a PM on a CDE400 DC Power Cable Connector and Pinouts OL-13478-03 Numerics IN-2 IN-3 IN-4 IN-5 IN-6