Cisco Systems 100/200/300/400 specifications Installing the Software, Model CDE200

Page 65

Chapter 4 Installing the Internet Streamer CDS Software and Initially Configuring a CDE

Installing the Software

b.If the USB CD-ROM drive is still not detected (not shown), press the Reset button again. If you are still unable to detect the CD-ROM drive at the BIOS level, contact Cisco Technical Support at the following URL:

www.cisco.com/techsupport

The system boots from the image on the CD. This requires a terminal server to be hooked up to the serial port of the CDE200. All communication is done through the serial port (see the “Before You Begin” section on page 4-1for terminal server settings.

Once the CD starts booting, it displays a spinning “” symbol for approximately five minutes. Allow the booting to proceed and monitor the sequence from a remote terminal provided by the terminal server.

The CD boot menu is displayed at the conclusion of this boot sequence:

Welcome to the installer. The installer enables installation of a new software image onto your system, or recovers a previous image in the event that the hardware was changed.

MODEL: CDE200

FLASH: found, directory validated

COOKIE: valid

IMAGE: DEVELOPMENT[jbohach-lnx02:/data/jbohach/ws/ipvideo/refact-dev-1

FLASHDEV: /dev/hdX

Installer Main Menu:

1.Configure Network

2.Manufacture flash

3.Install flash cookie

4.Install flash image from network

5.Install flash image from cdrom

6.Install flash image from disk

7.Wipe out disks and install.bin image

8.Exit (and reboot)

9.Force manufacturing flash

Choice [0]:

Step 14 Confirm that the FLASHDEV: line near the top of the menu displays something similar to “/dev/hdX”, where “X” can be any letter.

a.If no flash device is found, choose Option 8 to exit and reboot, and enter the BIOS Setup menu again. Confirm that the BIOS detected the flash device.

b.If the BIOS detects the CD-ROM drive but the CD installation menu is not displayed, this is an abnormal condition. You can use a different USB CD-ROM drive and attempt the procedure again, or contact Cisco Technical Support at the following URL:

www.cisco.com/techsupport

Installing the Software

Perform the following steps to install the software:

Step 1 Manufacture the IDE compact flash drive by selecting Option 2. This makes the IDE compact flash drive bootable. Enter Y to confirm the process.

 

 

Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide

 

 

 

 

 

 

OL-13478-03

 

 

4-13

 

 

 

 

 

Page 64 Page 66
Image 65
Page 64 Page 66
Contents Americas Headquarters MarchCisco Systems, Inc. All rights reserved N T E N T S Connecting Network Cables Ethernet Connector Pin Assignments B-2 OL-13478-03 Date Change Summary Document Revision HistoryDocument Organization Audience ObjectivesRelated Documentation Chapter DescriptionCisco Internet Streamer CDS 2.x Product Documentation Conventions Safety Information Referral WarningAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseAviso Instruções Importantes DE Segurança TA Vare PÅ Disse InstruksjoneneXii GEM Disse Anvisninger Xiv Obtaining Documentation and Submitting a Service Request Xvi Cisco Internet Streamer CDS Overview Overview of the Content Delivery EnginesVideo Accelerator Software Cisco TV CDS OverviewOnDemand Application CDE200 Front View Hardware FeaturesEth5 eth3 Interface Rack Unit EthernetProcessor Memory Drives Processor Memory Drives GE Ports Interface Control Buttons10 CDE200 Front Panel Control Buttons 12 CDE400 Back Panel Control Buttons LED IndicatorsColor State Description LED15 CDE300 Front Panel LEDs 17 CDE100 Connector Locations Input/Output Ports and ConnectorsCDE200 Connector Locations CDE400 Connector Locations OL-13478-03 Preventing Electrostatic Discharge Damage Site RequirementsEnvironmental, Physical, and Power Specifications Safety Warnings OL-13478-03 Page AC Power Option Warnings Safety GuidelinesDC Power Option Warnings General PrecautionsProtecting Against Electrostatic Discharge If AC Power Supplies Are Installed Safety InformationEmissions Disclaimer Intended UsesAmps Statement If DC Power Supplies Are InstalledTemperature and Ventilation Server Types Installing the Content Delivery EnginesUnpacking the Box Tools and Parts RequiredInspecting for Damage Verifying ContentsInstalling the CDEs Preparing the CDEs for Rack Installation Making Physical Connections Installing CDEs in the RackConnecting Power Cords CDE300 SX Version Connector Locations Connecting Network Cables Interface Switch Port Mbps Installing or Removing Disk DrivesCDE400 Disk Drive Locations Statement 11 Disk Drive Tray Installation and Removal Before You Begin Installation and Configuration Order Running the Bios Setup UtilityEthernet Management Gigabit Ethernet Ports Management Ports Ethernet StreamRunning the Bios Setup Utility for the CDE100 Boot Settings Menu Boot Device Priority Screen Advanced Settings Menu Set the Serial Port2 Address option to Disabled 10 Exit Options Screen Running the Bios Setup Utility for the CDE200 Set the QuickBoot Mode option to Enabled 14 Hard Disk Drives Screen Set the Com Port Address option to On-board COM a Model CDE200 Installing the SoftwareAssigning the Primary Interface Initially Configuring a CDEVerifying the Cdsm Running the Setup Utility18 Cdsm Login Documentation section on OL-13478-03 Troubleshooting Ethernet Adapters Hardware TroubleshootingTroubleshooting Sata Drives Specifications Technical SpecificationsCDE200 CDE100CDE400 CDE300Input Cables ManagementData Rate Description Pin Serial Console Interface Connector Pin AssignmentsSerial Port Connector Ethernet Connector Pin AssignmentsRJ-45 Pin End Wire Color Diagram End Ethernet Port ConnectorPin T568B 100BASE-T Signal Computer Cable Pin AssignmentsWhite/Orange White/Green Blue White/Blue White/Brown OL-13478-03 Fan Assembly WeightManagement Interface ProcessorIngest Interface Content Storage CapacityStream Interfaces TransportEthernet Interfaces Cached Content CapacityCDE200 IBM Scsi Controllers Figure C-1shows the location of all connectors for a CDE100 Connector Pin AssignmentsFigure C-3 CDE200 IBM Connector Locations Eth1 Eth0 Eth3 eth5 Eth6 Eth5 Eth8 Eth2 Eth4 Eth7 Eth1 Eth3 DC Power Overview Connecting DC PowerFigure D-2 CDE200 Rear Panel Connecting DC Power to a CDE200Star washer PM ground ring lug Nut Connecting DC Power to a CDE200 section on page D-2 Disconnecting Power and Replacing a PM on a CDE200Figure D-5 CDE300 Rear Panel Connecting DC Power to a CDE300Figure D-6 CDE300 Building/PM Ground Stud Order Disconnecting Power and Replacing a PM on a CDE300 Connecting DC Power to a CDE40048 VDC Figure D-8 CDE400 PM Ground Stud Order Disconnecting Power and Replacing a PM on a CDE400 DC Power Cable Connector and Pinouts OL-13478-03 Numerics IN-2 IN-3 IN-4 IN-5 IN-6
Top Page Image Contents