Tripp Lite SMART2200RM2U, SMART2600RM2U, SMART3000RM2UP, SMART3000RMXL2U Storage and Service

Page 17

Basic Operation continued

Output Breaker (select models): Your UPS features one or more breakers that protect your UPS from output overload. If one or more breakers trip, remove some of the load on the circuit(s), then reset them by pressing the breaker switch(es) in.

Ground Screw: Use this to connect any equipment that requires a chassis ground.

Storage and Service

Storage

Before storing your UPS, turn it completely OFF: with the UPS ON and receiving utility power, press and hold the “ON/OFF” button for two seconds (an alarm will beep once briefly after the interval has passed); then, unplug the UPS from the wall outlet. If you store your UPS for an extended period of time, recharge the UPS batteries once every three months: plug the UPS into a wall outlet; allow it to charge for 12 hours; and then unplug it and place it back in storage. If you leave your UPS batteries discharged for an extended period of time, they will suffer a permanent loss of capacity.

Service

A variety of Extended Warranty and On-Site Service Programs are also available from Tripp Lite. For more information on service, visit www.tripplite.com/support. Before returning your product for service, follow these steps:

1.Review the installation and operation procedures in this manual to insure that the service problem does not originate from a misreading of the instructions.

2.If the problem continues, do not contact or return the product to the dealer. Instead, visit www. tripplite.com/support.

3.If the problem requires service, visit www.tripplite.com/support and click the Product Returns link. From here you can request a Returned Material Authorization (RMA) number, which is required for service. This simple on-line form will ask for your unit’s model and serial numbers, along with other general purchaser information. The RMA number, along with shipping instructions will be emailed to you. Any damages (direct, indirect, special or consequential) to the product incurred during shipment to Tripp Lite or an authorized Tripp Lite service center is not covered under warranty. Products shipped to Tripp Lite or an authorized Tripp Lite service center must have transportation charges prepaid. Mark the RMA number on the outside of the package. If the product is within its warranty period, enclose a copy of your sales receipt.

Return the product for service using an insured carrier to the address given to you when you request the RMA.

17

12-12-037-93-3088-B.indb 17

12/26/2012 3:47:34 PM

Image 17
Contents Not suitable for mobile applications SmartPro 2U RackmountUPS Location Warnings Important Safety InstructionsUPS Connection Warnings Equipment Connection WarningsExternal Battery Connection Warnings Battery WarningsPost Mounting Mounting RackMounting Tower Turn the UPS on Quick InstallationEPO Port Connection Optional InstallationUSB and RS-232 Serial Communications External Battery Connection Select Models LCD Interface Mode ButtonBasic Operation 12-12-037-93-3088-B.indb 12/26/2012 34731 PM Basic Operation Minutes Load Wattage KWH/Day Display Power ConditionsControl Menu Options Enable/Disable AlarmLCD Brightness Self-testAVR Events On Battery EventsPower Sensitivity Factory Mode Reset External Battery Setting Control Select ModelsAC Outlets All models include Nema 5-15R and/or Nema Other UPS Features Rear PanelStorage Storage and ServiceService Battery Replacement Screws Always ensure that the battery Screws Remove Battery Retention Plate Connect BatteriesThem directly into the UPS cabinet Black-to-black and red-to-redTwo symbols are used on the label. V~ AC Voltage DC Voltage­ Warranty RegistrationNo adecuado para aplicaciones móviles Salida de Onda Sinusoidal de 120V Capacidades 2200VA-3000VAAdvertencias para la Ubicación del UPS Instrucciones de Seguridad ImportantesAdvertencias para la Conexión del UPS Advertencias sobre la conexión de equiposNo utilice el UPS sin baterías Advertencias sobre las bateríasAdvertencias para la Conexión de la Batería Externa Instalación en 4 Postes Instalación RackInstalación en 2 Postes Instalación Rack continuaciónInstalación Torre Conecte el UPS en un tomacorriente de un circuito dedicado Instalación RápidaEnchufe su equipo en el UPS Encienda el UPSConexión de Puerto EPO Instalación OpcionalComunicación Serial RS-232 y USB Del UPS, en Instalación Opcional continuaciónConexión de Baterías Externas Interfaz de LCD Operación BásicaOperación Básica continuación ACTIVAR-DESACTIVAR AlarmaOperación Básica continuación Batería Desplegado de las Condiciones de EnergíaEstimado Autonomía Estimado Minutes Watts de Carga KWH/Día Opciones del Menú de Control Activar/Desactivar AlarmaBrillo del LCD AutodiagnósticoSensibilidad de Energía Eventos de Batería en UsoEventos de AVR Restablecimiento del Modo de Fábrica Mensajes de ErrorControl de Calibración de Batería Externa Modelos Selectos Otras Características del UPS Panel Posterior Servicio Almacenamiento y ServicioAlmacenamiento Reemplazo de las Baterías Reemplazo de Baterías 12-12-037-93-3088-B.indb 12/26/2012 34815 PM Nota Sobre Etiquetado AvisosNe convient pas aux applications mobiles Sortie sinusoïdale de 120 V Capacités de 2 200 à 3 000 VAConsignes de sécurité importantes Avertissements concernant l’emplacement de l’ASCAvertissements concernant la connexion de l’ASC Avertissements concernant la connexion de l’équipementAvertissements concernant la batterie Montage sur bâti à 4 montants Montage bâtiMontage sur bâti à 2 montants Montage bâti suiteMontage tour Brancher l’ASC dans une prise d’un circuit dédié Installation rapideBrancher votre équipement dans l’ASC Mise sous tension de l’ASCConnexion au port EPO Installation en optionPorts de communication de série USB et RS-232 Connection de batterie Externe Installation en option suiteCommande » Bouton « Mode »Fonctionnement de base Interface ACLFonctionnement de base suite ACTIVATION-DÉSACTIVATION DE LalarmeIcône MIN Indique des unités de minutes Charge La batterie Affichage des conditions de puissanceEstimée en minutes Wattage de la KWh / jour Alarme activée / désactivée Options de menu de commandeCommande de défilement Luminosité ACLSensibilité à la puissance On Battery Events événements en mode batterieAVR Events événements AVR Message derreur Réinitialisation du mode Factory usineAutres fonctions de lASC panneau arrière Entreposage Entreposage et serviceRemplacement des batteries Ajouter de nouvelles batteries 12-12-037-93-3088-B.indb 12/26/2012 34845 PM Numéros d’identification de conformité aux règlements Avis12-12-037 93-3088RevF