Tripp Lite SMART3000RMXL2U, SMART2600RM2U Important Safety Instructions, UPS Location Warnings

Page 2

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during the installation, operation and storage of this product. Failure to heed these warnings may affect the warranty.

UPS Location Warnings

Use caution when lifting the UPS. Because of the considerable weight of all rackmount UPS systems, at least two people should assist in lifting and installing them.

Install the UPS indoors, away from excess moisture or heat, dust or direct sunlight.

For best performance, the ambient temperature near the UPS should be between 0° C and 40° C (between 32° F and 104° F).

Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct its vents or fan openings.

When mounting the UPS system in a tower orientation, make sure the LCD Screen panel is at the top of the UPS, not at the bottom.

Do not mount unit with its front or rear panel facing down (at any angle). Mounting in this manner will seriously inhibit the unit’s internal cooling, eventually causing product damage not covered under warranty.

UPS Connection Warnings

The UPS contains its own energy source (battery). The output terminals may be live even when the UPS is not connected to an AC supply.

Connect the UPS to a properly grounded AC power outlet. Do not modify the UPS’s plug in a way that would eliminate the UPS’s connection to ground. Do not use adapters that eliminate the UPS’s connection to ground.

Do not plug the UPS into itself; this will damage the UPS and void your warranty.

If you are connecting the UPS to a motor-powered AC generator, the generator must provide filtered, frequency-regulated computer-grade output. Connecting the UPS to a generator will void its Ultimate Lifetime Insurance.

Equipment Connection Warnings

Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide.

Do not connect surge suppressors or extension cords to the output of the UPS. This might damage the UPS and may affect the surge suppressor and UPS warranties.

 

2

12-12-037-93-3088-B.indb 2

12/26/2012 3:47:18 PM

Image 2
Contents SmartPro 2U Rackmount Not suitable for mobile applicationsUPS Connection Warnings Important Safety InstructionsUPS Location Warnings Equipment Connection WarningsBattery Warnings External Battery Connection WarningsMounting Rack Post MountingMounting Tower Quick Installation Turn the UPS onEPO Port Connection Optional InstallationUSB and RS-232 Serial Communications External Battery Connection Select Models LCD Interface Mode ButtonBasic Operation 12-12-037-93-3088-B.indb 12/26/2012 34731 PM Basic Operation Display Power Conditions Minutes Load Wattage KWH/DayLCD Brightness Enable/Disable AlarmControl Menu Options Self-testAVR Events On Battery EventsPower Sensitivity External Battery Setting Control Select Models Factory Mode ResetOther UPS Features Rear Panel AC Outlets All models include Nema 5-15R and/or NemaStorage Storage and ServiceService Battery Replacement Screws Them directly into the UPS cabinet Screws Remove Battery Retention Plate Connect BatteriesAlways ensure that the battery Black-to-black and red-to-redWarranty Registration Two symbols are used on the label. V~ AC Voltage DC Voltage­Salida de Onda Sinusoidal de 120V Capacidades 2200VA-3000VA No adecuado para aplicaciones móvilesAdvertencias para la Conexión del UPS Instrucciones de Seguridad ImportantesAdvertencias para la Ubicación del UPS Advertencias sobre la conexión de equiposNo utilice el UPS sin baterías Advertencias sobre las bateríasAdvertencias para la Conexión de la Batería Externa Instalación Rack Instalación en 4 PostesInstalación en 2 Postes Instalación Rack continuaciónInstalación Torre Enchufe su equipo en el UPS Instalación RápidaConecte el UPS en un tomacorriente de un circuito dedicado Encienda el UPSConexión de Puerto EPO Instalación OpcionalComunicación Serial RS-232 y USB Del UPS, en Instalación Opcional continuaciónConexión de Baterías Externas Operación Básica Interfaz de LCDACTIVAR-DESACTIVAR Alarma Operación Básica continuaciónOperación Básica continuación Batería Desplegado de las Condiciones de EnergíaEstimado Autonomía Estimado Minutes Watts de Carga KWH/Día Brillo del LCD Activar/Desactivar AlarmaOpciones del Menú de Control AutodiagnósticoSensibilidad de Energía Eventos de Batería en UsoEventos de AVR Restablecimiento del Modo de Fábrica Mensajes de ErrorControl de Calibración de Batería Externa Modelos Selectos Otras Características del UPS Panel Posterior Servicio Almacenamiento y ServicioAlmacenamiento Reemplazo de las Baterías Reemplazo de Baterías 12-12-037-93-3088-B.indb 12/26/2012 34815 PM Avisos Nota Sobre EtiquetadoSortie sinusoïdale de 120 V Capacités de 2 200 à 3 000 VA Ne convient pas aux applications mobilesAvertissements concernant la connexion de l’ASC Avertissements concernant l’emplacement de l’ASCConsignes de sécurité importantes Avertissements concernant la connexion de l’équipementAvertissements concernant la batterie Montage bâti Montage sur bâti à 4 montantsMontage sur bâti à 2 montants Montage bâti suiteMontage tour Brancher votre équipement dans l’ASC Installation rapideBrancher l’ASC dans une prise d’un circuit dédié Mise sous tension de l’ASCConnexion au port EPO Installation en optionPorts de communication de série USB et RS-232 Installation en option suite Connection de batterie ExterneFonctionnement de base Bouton « Mode »Commande » Interface ACLACTIVATION-DÉSACTIVATION DE Lalarme Fonctionnement de base suiteIcône MIN Indique des unités de minutes Charge La batterie Affichage des conditions de puissanceEstimée en minutes Wattage de la KWh / jour Commande de défilement Options de menu de commandeAlarme activée / désactivée Luminosité ACLSensibilité à la puissance On Battery Events événements en mode batterieAVR Events événements AVR Réinitialisation du mode Factory usine Message derreurAutres fonctions de lASC panneau arrière Entreposage et service EntreposageRemplacement des batteries Ajouter de nouvelles batteries 12-12-037-93-3088-B.indb 12/26/2012 34845 PM Avis Numéros d’identification de conformité aux règlements12-12-037 93-3088RevF