Patton electronic M-ATA manual Precautions, Safety when working with electricity

Page 15

SmartLink M-ATA Getting Started Guide

Precautions

Notes, cautions, and warnings, which have the following meanings, are used throughout this guide to help you become aware of potential problems. Warnings are intended to prevent safety hazards that could result in per- sonal injury. Cautions are intended to prevent situations that could result in property damage or

impaired functioning.

Note A note presents additional information or interesting sidelights.

The alert symbol and IMPORTANT heading calls attention to important information.

IMPORTANT

The alert symbol and CAUTION heading indicate a potential haz- ard. Strictly follow the instructions to avoid property damage.

CAUTION

The shock hazard symbol and CAUTION heading indicate a potential electric shock hazard. Strictly follow the instructions to avoid property damage caused by electric shock.

CAUTION

The alert symbol and WARNING heading indicate a potential safety hazard.

Strictly follow the warning instructions to avoid personal injury.

WARNING

The shock hazard symbol and WARNING heading indicate a potential electric shock hazard. Strictly follow the warning instructions to avoid injury caused by electric shock.

WARNING

Safety when working with electricity

WARNING

WARNING

The SmartLink contains no user serviceable parts. The equipment shall be returned to Patton Electronics for repairs, or repaired by qualiﬁed service personnel.

The external power adapter shall be a listed Limited Power Source. Ensure that the power cable used with this devise meets all applicable standards for the country in which it is to be installed, and that it is connected to a wall out- let which has earth ground. The mains outlet that is utilized to power the devise shall be within 10 feet (3 meters) of the device, shall be easily acces- sible, and protected by a circuit breaker.

15

Image 15

Contents SmartLink M-ATA Mailsupport@patton.com Summary Table of Contents Table of Contents Telephony None Table of Contents System Table of Contents Documentation Calling Features List of Figures List of Tables About this guide AudienceStructure Safety when working with electricity PrecautionsTypographical conventions used in this document General observationsGeneral conventions General information Chapter contentsSmartLink M-ATA SmartLink M-ATA overviewSmartLink installation Phone Power adapter Installing the M-ATAResetting the M-ATA to factory default System information System Uptime HomeSystem information System Status Network-LAN Network Settings StatusInterface Status Settings Internet Conﬁguration Obtain LAN conﬁguration dynamicallySpecify ﬁxed LAN conﬁguration WAN PPPoE Conﬁguration Enable PPPoEAuthentication SettingsVlan Conﬁguration Conﬁguring Dynamic DNSMAC Spooﬁng Conﬁguration WAN MAC Address SpoofedSaving your work ToS/DiffServVlan Tag Ieee 802.1q Priority Tag Ieee 802.1qTelephony Telephony Telephony VoIP Status VoIP Server Registration StatusPhone Line Status Messages waiting Caller ID SettingUser Name Subscribed for VoicemailSIP Server Settings Gateway SettingsSIP Conﬁguration SIP Extensions RTP Telephone Event ConﬁgurationVoIP Vlan Conﬁguration RTP Parameters SIP Timer Values millisecondsSIP Parameters Hook Flash Mime TypeNAT Traversal FAX without T.38 Use G.711 fax Audio/CODEC ConﬁgurationPacketization Jitter BufferUser Information PhoneSupplementary Service Activation Dialing by IP Address Message Waiting IndicatorDistinctive Ring Call TransferDial Out Type Call Forward SettingsSelective Call Forward Settings Incoming Call BlockOutgoing Call Block Speed Dial Serv Http Digest SettingLine 1 Speed Dial Settings Speed DialSystem System System Conﬁrm new password Set Security PasswordNew Root Password New User PasswordSyslog Server Syslog ServiceEnable Syslog ConﬁgurationDebug Server Debug ServiceEnable Debug NTP ServiceEnable Ping Reply Service AccessTime Zone Adjust clock for daylight savings Enable HttpCall Progress Tones LocalizationHolding Tone Dial TonePrompt Tone Conﬁrm ToneFollowing is a sample ring cadence pattern conﬁguration Distinctive Ring SettingsWarm Line Supplementary Service KeysCall forward selective Block Anonymous CallsCalling Preﬁx Keys IP DialingSpeed Dialing Income Caller IDCall Conference Drop Call HoldCall Waiting call alternative Call ConferenceControl Timer Values FXS Port FXS Port Polarity Conﬁguration Ring SettingSnmp System Conﬁguration Snmp ConﬁgurationSnmp Trap Conﬁguration Snmp Community ConﬁgurationAuto Upgrade Manual Upgrade window Manual UpgradeReload Documentation Documentation link IntroductionLogout Logout window Contacting Patton for assistance Patton support headquarters in the USA Contact informationRMA numbers Warranty coverageAppendix a Compliance information CE Notice Declarations of Conformity Safety ComplianceCompliance Radio and TV Interference FCC PartAppendix B Speciﬁcations Fax and Modem Support Voice Processing signalling dependentVoice Connectivity ConnectivityOperating Environment Voice Services/FeaturesIP Services ManagementAppendix C Dial plans Complex Dial Plan Sample Dial PlansSimple Dial Plan Non-dialed Line Dial PlanSample Dial Plans Appendix D Calling Features Distinctive on Distinctive OFF Appendix E Voice prompt conﬁguration Existing voice prompt conﬁguration Accessing the voice prompt