Patton electronic M-ATA manual SIP Configuration, SIP Server Settings, Gateway Settings

Page 37

SmartLink M-ATA Getting Started Guide

5 • Telephony

 

 

SIP Configuration

Figure 12. SIP Configuration section of the SIP window

SIP Server Settings

The SmartLink M-ATA will automatically attempt to locate the VoIP server by using the domain name speci- fied in the LAN interface or the server will be discovered via DHCP on the WAN interface. When found, the discovered server will be listed as the Current Server.

Enter the following information:

•Server address—The IP address or domain name hosting the VoIP SIP server

•Port—The UDP port of the VoIP SIP server. The default is 5060.

•Domain name—The VoIP domain name (realm) is used for validation of each phone’s username

•Send Registration Request with Expire Time—If selected, determines the amount of time (in seconds) that the SIP registration will be valid for.

•Unregistration—If checked, the SmartLink will send a SIP unregister at system reload before sending a SIP registration request.

•Send SUBSCRIBE—If checked, the SmartLink will send a SIP subscribe to the server specified. This box must be checked for the voicemail message counted and message waiting notification to work.

•SUBSCRIBE Server IP or FQDN—The IP address or fully qualified domain name of the subscription ser- vice. If not specified, the SIP subscribes to the SIP server.

Figure 13. Gateway Settings section of the SIP window

Gateway Settings

Dial Plan. Refer to appendix C, “Dial plans” on page 80

SIP

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents SmartLink M-ATA Mailsupport@patton.com Summary Table of Contents Table of Contents Telephony None Table of Contents System Table of Contents Documentation Calling Features List of Figures List of Tables Audience About this guideStructure Safety when working with electricity PrecautionsGeneral observations Typographical conventions used in this documentGeneral conventions General information Chapter contentsSmartLink M-ATA SmartLink M-ATA overviewSmartLink installation Phone Power adapter Installing the M-ATAResetting the M-ATA to factory default System information System Uptime HomeSystem information System Status Network-LAN Status Network SettingsInterface Status Settings Obtain LAN configuration dynamically Internet ConfigurationSpecify fixed LAN configuration Authentication Enable PPPoESettings WAN PPPoE ConfigurationMAC Spoofing Configuration Configuring Dynamic DNSWAN MAC Address Spoofed Vlan ConfigurationVlan Tag Ieee 802.1q ToS/DiffServPriority Tag Ieee 802.1q Saving your workTelephony Telephony Telephony VoIP Server Registration Status VoIP StatusPhone Line Status User Name Caller ID SettingSubscribed for Voicemail Messages waitingGateway Settings SIP Server SettingsSIP Configuration RTP Telephone Event Configuration SIP ExtensionsVoIP Vlan Configuration SIP Parameters SIP Timer Values millisecondsHook Flash Mime Type RTP ParametersNAT Traversal Packetization Audio/CODEC ConfigurationJitter Buffer FAX without T.38 Use G.711 faxUser Information PhoneSupplementary Service Activation Distinctive Ring Message Waiting IndicatorCall Transfer Dialing by IP AddressDial Out Type Call Forward SettingsIncoming Call Block Selective Call Forward SettingsOutgoing Call Block Line 1 Speed Dial Settings Http Digest SettingSpeed Dial Speed Dial ServSystem System System New Root Password Set Security PasswordNew User Password Confirm new passwordEnable Syslog Syslog ServiceConfiguration Syslog ServerEnable Debug Debug ServiceNTP Service Debug ServerTime Zone Adjust clock for daylight savings Service AccessEnable Http Enable Ping ReplyCall Progress Tones LocalizationPrompt Tone Dial ToneConfirm Tone Holding ToneFollowing is a sample ring cadence pattern configuration Distinctive Ring SettingsCall forward selective Supplementary Service KeysBlock Anonymous Calls Warm LineSpeed Dialing IP DialingIncome Caller ID Calling Prefix KeysCall Waiting call alternative Call HoldCall Conference Call Conference DropControl Timer Values FXS Port FXS Port Polarity Configuration Ring SettingSnmp Trap Configuration Snmp ConfigurationSnmp Community Configuration Snmp System ConfigurationAuto Upgrade Manual Upgrade window Manual UpgradeReload Documentation Documentation link IntroductionLogout Logout window Contacting Patton for assistance Patton support headquarters in the USA Contact informationRMA numbers Warranty coverageAppendix a Compliance information Compliance Safety ComplianceRadio and TV Interference FCC Part CE Notice Declarations of ConformityAppendix B Specifications Voice Connectivity Voice Processing signalling dependentConnectivity Fax and Modem SupportIP Services Voice Services/FeaturesManagement Operating EnvironmentAppendix C Dial plans Simple Dial Plan Sample Dial PlansNon-dialed Line Dial Plan Complex Dial PlanSample Dial Plans Appendix D Calling Features Distinctive on Distinctive OFF Appendix E Voice prompt configuration Existing voice prompt configuration Accessing the voice prompt
Top Page Image Contents