Patton electronic M-ATA manual Interface Status, Network Settings

Page 26

SmartLink M-ATA Getting Started Guide	4 • Network—LAN

Status

Shows the status of key LAN network settings as conﬁgured under LAN settings

Interface Status

Figure 4. Internet Status window

Enabled

Yes indicates the LAN interface is enabled and ready to be used.

Service

Either Routed or Bridged, displays whether the SmartLink’s LAN interface connection is operating in a routed or bridged mode.

Interface Status

Either Up or Down.

Network Settings

These are the details of your LAN network settings.

Dynamic IP Assignment

Displays Yes (via DHCP) if you are using a dynamic IP address or No if a dynamic IP address is not being used.

Status

26

Image 26

Contents SmartLink M-ATA Mailsupport@patton.com Summary Table of Contents Table of Contents Telephony None Table of Contents System Table of Contents Documentation Calling Features List of Figures List of Tables Structure About this guideAudience Precautions Safety when working with electricityGeneral conventions Typographical conventions used in this documentGeneral observations Chapter contents General informationSmartLink M-ATA overview SmartLink M-ATASmartLink installation Installing the M-ATA Phone Power adapterResetting the M-ATA to factory default Home System information System UptimeSystem information System Status Network-LAN Interface Status Network SettingsStatus Settings Specify ﬁxed LAN conﬁguration Internet ConﬁgurationObtain LAN conﬁguration dynamically Settings Enable PPPoEAuthentication WAN PPPoE ConﬁgurationWAN MAC Address Spoofed Conﬁguring Dynamic DNSMAC Spooﬁng Conﬁguration Vlan ConﬁgurationPriority Tag Ieee 802.1q ToS/DiffServVlan Tag Ieee 802.1q Saving your workTelephony Telephony Telephony Phone Line Status VoIP StatusVoIP Server Registration Status Subscribed for Voicemail Caller ID SettingUser Name Messages waitingSIP Conﬁguration SIP Server SettingsGateway Settings VoIP Vlan Conﬁguration SIP ExtensionsRTP Telephone Event Conﬁguration Hook Flash Mime Type SIP Timer Values millisecondsSIP Parameters RTP ParametersNAT Traversal Jitter Buffer Audio/CODEC ConﬁgurationPacketization FAX without T.38 Use G.711 faxPhone User InformationSupplementary Service Activation Call Transfer Message Waiting IndicatorDistinctive Ring Dialing by IP AddressCall Forward Settings Dial Out TypeOutgoing Call Block Selective Call Forward SettingsIncoming Call Block Speed Dial Http Digest SettingLine 1 Speed Dial Settings Speed Dial ServSystem System System New User Password Set Security PasswordNew Root Password Conﬁrm new passwordConﬁguration Syslog ServiceEnable Syslog Syslog ServerNTP Service Debug ServiceEnable Debug Debug ServerEnable Http Service AccessTime Zone Adjust clock for daylight savings Enable Ping ReplyLocalization Call Progress TonesConﬁrm Tone Dial TonePrompt Tone Holding ToneDistinctive Ring Settings Following is a sample ring cadence pattern conﬁgurationBlock Anonymous Calls Supplementary Service KeysCall forward selective Warm LineIncome Caller ID IP DialingSpeed Dialing Calling Preﬁx KeysCall Conference Call HoldCall Waiting call alternative Call Conference DropControl Timer Values FXS Port Ring Setting FXS Port Polarity ConﬁgurationSnmp Community Conﬁguration Snmp ConﬁgurationSnmp Trap Conﬁguration Snmp System ConﬁgurationAuto Upgrade Manual Upgrade Manual Upgrade windowReload Documentation Introduction Documentation linkLogout Logout window Contacting Patton for assistance Contact information Patton support headquarters in the USAWarranty coverage RMA numbersAppendix a Compliance information Radio and TV Interference FCC Part Safety ComplianceCompliance CE Notice Declarations of ConformityAppendix B Speciﬁcations Connectivity Voice Processing signalling dependentVoice Connectivity Fax and Modem SupportManagement Voice Services/FeaturesIP Services Operating EnvironmentAppendix C Dial plans Non-dialed Line Dial Plan Sample Dial PlansSimple Dial Plan Complex Dial PlanSample Dial Plans Appendix D Calling Features Distinctive on Distinctive OFF Appendix E Voice prompt conﬁguration Accessing the voice prompt Existing voice prompt conﬁguration