Patton electronic M-ATA manual Control Timer Values

Page 61

SmartLink M-ATA Getting Started Guide

6 • System

 

 

Voicemail access

Configures the key sequence for call for voicemail access. The factory default is flash hook *86. If the voicemail key sequence is entered on the phone a call will automatically be placed to the configured service provider using the configured authentication information.

Call Forward Busy Destination

Configures the number to forward calls to when busy. To configure call forward busy enter the calling prefix key (*74 is the factory default), the number to dial and then on hook the phone. You will hear a second dial tone after entering the calling prefix key. Before using, call forward busy must be enabled using the activate sequence defined in the supplementary service table.

Example:

*743019751000 and on-hook the phone. All calls received will forward to 3019751000 when the phone is busy.

Hotline

Configures the number to call when the telephone goes off hook. To configure the hotline number enter the calling prefix key (*75 is the factory default), the number to dial and then on hook the phone. You will hear a second dial tone after entering the calling prefix key. Before using hotline calling it must be enabled using the activate sequence defined in the supplementary service table.

Example:

*753019751000 and on-hook the phone. When the handset is lifted, 3019751000 will immediately be called.

Control Timer Values

Figure 36. Control Timer Values section of Localization window

Hook Flash Timer

Maximum on-hook time before off-hook to qualify as hookflash. More than this value and the on-hook event is treated as on-hook (hanging up the call).

Minimum on-hook time before off-hook to qualify as hookflash. At less than this value, the on-hook event is ignored.

SIP Session Timer value

The amount of time the SmartLink M-ATA will wait during an active call to send repeated re-invites on active calls to allow the SIP server to determine the status of a call.

Localization

61

Image 61
Contents SmartLink M-ATA Mailsupport@patton.com Summary Table of Contents Table of Contents Telephony None Table of Contents System Table of Contents Documentation Calling Features List of Figures List of Tables Audience About this guideStructure Safety when working with electricity PrecautionsGeneral observations Typographical conventions used in this documentGeneral conventions General information Chapter contentsSmartLink M-ATA SmartLink M-ATA overviewSmartLink installation Phone Power adapter Installing the M-ATAResetting the M-ATA to factory default System information System Uptime HomeSystem information System Status Network-LAN Status Network SettingsInterface Status Settings Obtain LAN configuration dynamically Internet ConfigurationSpecify fixed LAN configuration Authentication Enable PPPoESettings WAN PPPoE ConfigurationMAC Spoofing Configuration Configuring Dynamic DNSWAN MAC Address Spoofed Vlan ConfigurationVlan Tag Ieee 802.1q ToS/DiffServPriority Tag Ieee 802.1q Saving your workTelephony Telephony Telephony VoIP Server Registration Status VoIP StatusPhone Line Status User Name Caller ID SettingSubscribed for Voicemail Messages waitingGateway Settings SIP Server SettingsSIP Configuration RTP Telephone Event Configuration SIP ExtensionsVoIP Vlan Configuration SIP Parameters SIP Timer Values millisecondsHook Flash Mime Type RTP ParametersNAT Traversal Packetization Audio/CODEC ConfigurationJitter Buffer FAX without T.38 Use G.711 faxUser Information PhoneSupplementary Service Activation Distinctive Ring Message Waiting IndicatorCall Transfer Dialing by IP AddressDial Out Type Call Forward SettingsIncoming Call Block Selective Call Forward SettingsOutgoing Call Block Line 1 Speed Dial Settings Http Digest SettingSpeed Dial Speed Dial ServSystem System System New Root Password Set Security PasswordNew User Password Confirm new passwordEnable Syslog Syslog ServiceConfiguration Syslog ServerEnable Debug Debug ServiceNTP Service Debug ServerTime Zone Adjust clock for daylight savings Service AccessEnable Http Enable Ping ReplyCall Progress Tones LocalizationPrompt Tone Dial ToneConfirm Tone Holding ToneFollowing is a sample ring cadence pattern configuration Distinctive Ring SettingsCall forward selective Supplementary Service KeysBlock Anonymous Calls Warm LineSpeed Dialing IP DialingIncome Caller ID Calling Prefix KeysCall Waiting call alternative Call HoldCall Conference Call Conference DropControl Timer Values FXS Port FXS Port Polarity Configuration Ring SettingSnmp Trap Configuration Snmp ConfigurationSnmp Community Configuration Snmp System ConfigurationAuto Upgrade Manual Upgrade window Manual UpgradeReload Documentation Documentation link IntroductionLogout Logout window Contacting Patton for assistance Patton support headquarters in the USA Contact informationRMA numbers Warranty coverageAppendix a Compliance information Compliance Safety ComplianceRadio and TV Interference FCC Part CE Notice Declarations of ConformityAppendix B Specifications Voice Connectivity Voice Processing signalling dependentConnectivity Fax and Modem SupportIP Services Voice Services/FeaturesManagement Operating EnvironmentAppendix C Dial plans Simple Dial Plan Sample Dial PlansNon-dialed Line Dial Plan Complex Dial PlanSample Dial Plans Appendix D Calling Features Distinctive on Distinctive OFF Appendix E Voice prompt configuration Existing voice prompt configuration Accessing the voice prompt