Patton electronic M-ATA manual Manual Upgrade window

Page 66

SmartLink M-ATA Getting Started Guide	6 • System

Manual Upgrade

For both HTTP and TFTP methods, the device will reboot itself into the downloader mode if the main appli- cation is executing, and proceed with the ROM ﬁle download and permanent write of the application to the device’s ﬂash memory. During download of new ﬁrmware images, the LEDs on the SmartLink M-ATA will ﬂash sequentially. Typically, HTTP downloads take about 5–10 minutes. After the download is completed, the download status page will be displayed.

Figure 42. Manual Upgrade window

Manual Upgrade

66

Image 66

Contents SmartLink M-ATA Mailsupport@patton.com Summary Table of Contents Table of Contents Telephony None Table of Contents System Table of Contents Documentation Calling Features List of Figures List of Tables About this guide AudienceStructure Precautions Safety when working with electricityTypographical conventions used in this document General observationsGeneral conventions Chapter contents General informationSmartLink M-ATA overview SmartLink M-ATASmartLink installation Installing the M-ATA Phone Power adapterResetting the M-ATA to factory default Home System information System UptimeSystem information System Status Network-LAN Network Settings StatusInterface Status Settings Internet Conﬁguration Obtain LAN conﬁguration dynamicallySpecify ﬁxed LAN conﬁguration Settings Enable PPPoEAuthentication WAN PPPoE ConﬁgurationWAN MAC Address Spoofed Conﬁguring Dynamic DNSMAC Spooﬁng Conﬁguration Vlan ConﬁgurationPriority Tag Ieee 802.1q ToS/DiffServVlan Tag Ieee 802.1q Saving your workTelephony Telephony Telephony VoIP Status VoIP Server Registration StatusPhone Line Status Subscribed for Voicemail Caller ID SettingUser Name Messages waitingSIP Server Settings Gateway SettingsSIP Conﬁguration SIP Extensions RTP Telephone Event ConﬁgurationVoIP Vlan Conﬁguration Hook Flash Mime Type SIP Timer Values millisecondsSIP Parameters RTP ParametersNAT Traversal Jitter Buffer Audio/CODEC ConﬁgurationPacketization FAX without T.38 Use G.711 faxPhone User InformationSupplementary Service Activation Call Transfer Message Waiting IndicatorDistinctive Ring Dialing by IP AddressCall Forward Settings Dial Out TypeSelective Call Forward Settings Incoming Call BlockOutgoing Call Block Speed Dial Http Digest SettingLine 1 Speed Dial Settings Speed Dial ServSystem System System New User Password Set Security PasswordNew Root Password Conﬁrm new passwordConﬁguration Syslog ServiceEnable Syslog Syslog ServerNTP Service Debug ServiceEnable Debug Debug ServerEnable Http Service AccessTime Zone Adjust clock for daylight savings Enable Ping ReplyLocalization Call Progress TonesConﬁrm Tone Dial TonePrompt Tone Holding ToneDistinctive Ring Settings Following is a sample ring cadence pattern conﬁgurationBlock Anonymous Calls Supplementary Service KeysCall forward selective Warm LineIncome Caller ID IP DialingSpeed Dialing Calling Preﬁx KeysCall Conference Call HoldCall Waiting call alternative Call Conference DropControl Timer Values FXS Port Ring Setting FXS Port Polarity ConﬁgurationSnmp Community Conﬁguration Snmp ConﬁgurationSnmp Trap Conﬁguration Snmp System ConﬁgurationAuto Upgrade Manual Upgrade Manual Upgrade windowReload Documentation Introduction Documentation linkLogout Logout window Contacting Patton for assistance Contact information Patton support headquarters in the USAWarranty coverage RMA numbersAppendix a Compliance information Radio and TV Interference FCC Part Safety ComplianceCompliance CE Notice Declarations of ConformityAppendix B Speciﬁcations Connectivity Voice Processing signalling dependentVoice Connectivity Fax and Modem SupportManagement Voice Services/FeaturesIP Services Operating EnvironmentAppendix C Dial plans Non-dialed Line Dial Plan Sample Dial PlansSimple Dial Plan Complex Dial PlanSample Dial Plans Appendix D Calling Features Distinctive on Distinctive OFF Appendix E Voice prompt conﬁguration Accessing the voice prompt Existing voice prompt conﬁguration