Patton electronic M-ATA User Name, Caller ID Setting, Subscribed for Voicemail, Messages waiting

Page 36

SmartLink M-ATA Getting Started Guide

5 • Telephony

 

 

•No Registration—The SmartLink M-ATA is not attempting to register with the SIP server because “Send Registration Request” is not checked on SIP sever setting screen.

•Error: Not Authorized—A SIP final status message status of 401 or 407 has been received from the SIP server.

•Error: Forbidden—SIP final status message status of 401 or 407 has been received from the SIP server.

•Error 408: Request timeout— A SIP final status message status of 408 has been received from the SIP server.

•Response: xxx—A SIP final status message status of xxx has been received from the SIP server.

User Name

The authentication username that was specified under section “Phone 1” on page 42. This user name will be used to register with the VoIP server.

Caller ID Setting

The Caller ID name setting that was specified under section “Phone 1” on page 42. This is the display name that others will see as your caller id when you make a call.

Subscribed for Voicemail

Shows if the SIP Subscribe message was successful for this phone line. If “Yes”, then the subscription process was successful. The number of voicemail messages in the queue will not be provided if the subscription for voice mail fails.

Messages waiting

After successful subscription to the SIP server, the SIP server/Internet Telephony service provider should send the number of voicemail messages that are queued up for the user using the SIP Notify message. The messages waiting shows the number of normal priority new messages, normal priority old (listened to) messages, num- ber of urgent priority new voicemail messages and the number of old (listened to) urgent priority voicemail messages as reported to the SmartLink M-ATA by the VoIP SIP server.

SIP

The SIP window contains the following sections:

•SIP Configuration (see figure 12 on page 37)

•SIP Extensions (see figure 14 on page 38)

•RTP Telephone Event Configuration (see figure 15 on page 38)

•VoIP VLAN Configuration (see figure 16 on page 39)

•SIP Parameters (see figure 17 on page 39)

•NAT Traversal (see figure 18 on page 40)

Note After configuring the sections, click the Save SIP Settings button (see figure 18 on page 40) to save the new configuration.

SIP

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents SmartLink M-ATA Mailsupport@patton.com Summary Table of Contents Table of Contents Telephony None Table of Contents System Table of Contents Documentation Calling Features List of Figures List of Tables About this guide AudienceStructure Precautions Safety when working with electricityTypographical conventions used in this document General observationsGeneral conventions Chapter contents General informationSmartLink M-ATA overview SmartLink M-ATASmartLink installation Installing the M-ATA Phone Power adapterResetting the M-ATA to factory default Home System information System UptimeSystem information System Status Network-LAN Network Settings StatusInterface Status Settings Internet Configuration Obtain LAN configuration dynamicallySpecify fixed LAN configuration Enable PPPoE AuthenticationSettings WAN PPPoE ConfigurationConfiguring Dynamic DNS MAC Spoofing ConfigurationWAN MAC Address Spoofed Vlan ConfigurationToS/DiffServ Vlan Tag Ieee 802.1qPriority Tag Ieee 802.1q Saving your workTelephony Telephony Telephony VoIP Status VoIP Server Registration StatusPhone Line Status Caller ID Setting User NameSubscribed for Voicemail Messages waitingSIP Server Settings Gateway SettingsSIP Configuration SIP Extensions RTP Telephone Event ConfigurationVoIP Vlan Configuration SIP Timer Values milliseconds SIP ParametersHook Flash Mime Type RTP ParametersNAT Traversal Audio/CODEC Configuration PacketizationJitter Buffer FAX without T.38 Use G.711 faxPhone User InformationSupplementary Service Activation Message Waiting Indicator Distinctive RingCall Transfer Dialing by IP AddressCall Forward Settings Dial Out TypeSelective Call Forward Settings Incoming Call BlockOutgoing Call Block Http Digest Setting Line 1 Speed Dial SettingsSpeed Dial Speed Dial ServSystem System System Set Security Password New Root PasswordNew User Password Confirm new passwordSyslog Service Enable SyslogConfiguration Syslog ServerDebug Service Enable DebugNTP Service Debug ServerService Access Time Zone Adjust clock for daylight savingsEnable Http Enable Ping ReplyLocalization Call Progress TonesDial Tone Prompt ToneConfirm Tone Holding ToneDistinctive Ring Settings Following is a sample ring cadence pattern configurationSupplementary Service Keys Call forward selectiveBlock Anonymous Calls Warm LineIP Dialing Speed DialingIncome Caller ID Calling Prefix KeysCall Hold Call Waiting call alternativeCall Conference Call Conference DropControl Timer Values FXS Port Ring Setting FXS Port Polarity ConfigurationSnmp Configuration Snmp Trap ConfigurationSnmp Community Configuration Snmp System ConfigurationAuto Upgrade Manual Upgrade Manual Upgrade windowReload Documentation Introduction Documentation linkLogout Logout window Contacting Patton for assistance Contact information Patton support headquarters in the USAWarranty coverage RMA numbersAppendix a Compliance information Safety Compliance ComplianceRadio and TV Interference FCC Part CE Notice Declarations of ConformityAppendix B Specifications Voice Processing signalling dependent Voice ConnectivityConnectivity Fax and Modem SupportVoice Services/Features IP ServicesManagement Operating EnvironmentAppendix C Dial plans Sample Dial Plans Simple Dial PlanNon-dialed Line Dial Plan Complex Dial PlanSample Dial Plans Appendix D Calling Features Distinctive on Distinctive OFF Appendix E Voice prompt configuration Accessing the voice prompt Existing voice prompt configuration
Top Page Image Contents