Patton electronic M-ATA manual FXS Port

Page 62

SmartLink M-ATA Getting Started Guide

6 • System

 

 

Conditional Call Forwarding Timer

Specified a time period as a call forward condition. After the number of seconds specified, the conditional call forwarding process will be performed.

Warm Line Delay

Specify a time period as a delay time for warm line dialing. If warm line is enabled, then the SmartLink M-ATA will wait this amount of time after the handset is off-hook before dialing the warm line phone number.

Interdigit Timer

The number of seconds the SmartLink M-ATA will wait for the caller to input a subsequent digit of the dialed number. If the timer value is exceeded before the dial plan is matched (see section “Gateway Settings” on page 37), the busy tone will be played to the caller.

Offhook Idle Time

If the handset is off-hook with no dialing activity for longer than the time specified, then the busy tone will be played. The default is 6000 ms (6 seconds).

Offhook Warning tone time

If the handset is off-hook with no dialing activity for longer than the time specified, then the off-hook warning tone will be played. The default is 12000 ms (12 seconds). This value should be greater than the off-hook idle time (see section “Offhook Idle Time”).

FXS Port

Choose the correct country for a proper impedance match.

Figure 37. FXS Port Polarity Configuration section of Localization window

FXS port Input Gain

Adjust the input gain level for FXS port.

FXS port Output Gain

Adjust the output gain level for FXS port.

Caller ID Method

Specifies the country-specific Caller ID format.

“Call Progress Tones” Synchronization

When “Call Progress Tones” Synchronization is selected, the Caller ID presentation method value is used to auto- matically set the county-specific call progress tones.

Localization

62

Page 61 Page 63
Image 62
Page 61 Page 63
Contents SmartLink M-ATA Mailsupport@patton.com Summary Table of Contents Table of Contents Telephony None Table of Contents System Table of Contents Documentation Calling Features List of Figures List of Tables Structure About this guideAudience Precautions Safety when working with electricityGeneral conventions Typographical conventions used in this documentGeneral observations Chapter contents General informationSmartLink M-ATA overview SmartLink M-ATASmartLink installation Installing the M-ATA Phone Power adapterResetting the M-ATA to factory default Home System information System UptimeSystem information System Status Network-LAN Interface Status Network SettingsStatus Settings Specify fixed LAN configuration Internet ConfigurationObtain LAN configuration dynamically Settings Enable PPPoEAuthentication WAN PPPoE ConfigurationWAN MAC Address Spoofed Configuring Dynamic DNSMAC Spoofing Configuration Vlan ConfigurationPriority Tag Ieee 802.1q ToS/DiffServVlan Tag Ieee 802.1q Saving your workTelephony Telephony Telephony Phone Line Status VoIP StatusVoIP Server Registration Status Subscribed for Voicemail Caller ID SettingUser Name Messages waitingSIP Configuration SIP Server SettingsGateway Settings VoIP Vlan Configuration SIP ExtensionsRTP Telephone Event Configuration Hook Flash Mime Type SIP Timer Values millisecondsSIP Parameters RTP ParametersNAT Traversal Jitter Buffer Audio/CODEC ConfigurationPacketization FAX without T.38 Use G.711 faxPhone User InformationSupplementary Service Activation Call Transfer Message Waiting IndicatorDistinctive Ring Dialing by IP AddressCall Forward Settings Dial Out TypeOutgoing Call Block Selective Call Forward SettingsIncoming Call Block Speed Dial Http Digest SettingLine 1 Speed Dial Settings Speed Dial ServSystem System System New User Password Set Security PasswordNew Root Password Confirm new passwordConfiguration Syslog ServiceEnable Syslog Syslog ServerNTP Service Debug ServiceEnable Debug Debug ServerEnable Http Service AccessTime Zone Adjust clock for daylight savings Enable Ping ReplyLocalization Call Progress TonesConfirm Tone Dial TonePrompt Tone Holding ToneDistinctive Ring Settings Following is a sample ring cadence pattern configurationBlock Anonymous Calls Supplementary Service KeysCall forward selective Warm LineIncome Caller ID IP DialingSpeed Dialing Calling Prefix KeysCall Conference Call HoldCall Waiting call alternative Call Conference DropControl Timer Values FXS Port Ring Setting FXS Port Polarity ConfigurationSnmp Community Configuration Snmp ConfigurationSnmp Trap Configuration Snmp System ConfigurationAuto Upgrade Manual Upgrade Manual Upgrade windowReload Documentation Introduction Documentation linkLogout Logout window Contacting Patton for assistance Contact information Patton support headquarters in the USAWarranty coverage RMA numbersAppendix a Compliance information Radio and TV Interference FCC Part Safety ComplianceCompliance CE Notice Declarations of ConformityAppendix B Specifications Connectivity Voice Processing signalling dependentVoice Connectivity Fax and Modem SupportManagement Voice Services/FeaturesIP Services Operating EnvironmentAppendix C Dial plans Non-dialed Line Dial Plan Sample Dial PlansSimple Dial Plan Complex Dial PlanSample Dial Plans Appendix D Calling Features Distinctive on Distinctive OFF Appendix E Voice prompt configuration Accessing the voice prompt Existing voice prompt configuration
Top Page Image Contents