Patton electronic M-ATA manual Ring Setting, FXS Port Polarity Conﬁguration

Page 63

SmartLink M-ATA Getting Started Guide	6 • System

Ring Setting

Figure 38. Ring Setting section of Localization window

Ring Waveform

Specify the ring tone waveform.

Ring Frequency

Specify the ring tone frequency.

Ring Voltage

Specify the ring tone voltage.

FXS Port Polarity Conﬁguration

Figure 39. FXS Port Polarity section of Localization window

Idle Polarity

Polarity before call connected.

Caller Conn Polarity

Polarity after outbound call connected.

Saving your work

When you are ﬁnished conﬁguring settings, click the Save button (see ﬁgure 39) to save the changes.

Localization

63

Image 63

Contents SmartLink M-ATA Mailsupport@patton.com Summary Table of Contents Table of Contents Telephony None Table of Contents System Table of Contents Documentation Calling Features List of Figures List of Tables About this guide AudienceStructure Safety when working with electricity PrecautionsTypographical conventions used in this document General observationsGeneral conventions General information Chapter contentsSmartLink M-ATA SmartLink M-ATA overviewSmartLink installation Phone Power adapter Installing the M-ATAResetting the M-ATA to factory default System information System Uptime HomeSystem information System Status Network-LAN Network Settings StatusInterface Status Settings Internet Conﬁguration Obtain LAN conﬁguration dynamicallySpecify ﬁxed LAN conﬁguration WAN PPPoE Conﬁguration Enable PPPoEAuthentication SettingsVlan Conﬁguration Conﬁguring Dynamic DNSMAC Spooﬁng Conﬁguration WAN MAC Address SpoofedSaving your work ToS/DiffServVlan Tag Ieee 802.1q Priority Tag Ieee 802.1qTelephony Telephony Telephony VoIP Status VoIP Server Registration StatusPhone Line Status Messages waiting Caller ID SettingUser Name Subscribed for VoicemailSIP Server Settings Gateway SettingsSIP Conﬁguration SIP Extensions RTP Telephone Event ConﬁgurationVoIP Vlan Conﬁguration RTP Parameters SIP Timer Values millisecondsSIP Parameters Hook Flash Mime TypeNAT Traversal FAX without T.38 Use G.711 fax Audio/CODEC ConﬁgurationPacketization Jitter BufferUser Information PhoneSupplementary Service Activation Dialing by IP Address Message Waiting IndicatorDistinctive Ring Call TransferDial Out Type Call Forward SettingsSelective Call Forward Settings Incoming Call BlockOutgoing Call Block Speed Dial Serv Http Digest SettingLine 1 Speed Dial Settings Speed DialSystem System System Conﬁrm new password Set Security PasswordNew Root Password New User PasswordSyslog Server Syslog ServiceEnable Syslog ConﬁgurationDebug Server Debug ServiceEnable Debug NTP ServiceEnable Ping Reply Service AccessTime Zone Adjust clock for daylight savings Enable HttpCall Progress Tones LocalizationHolding Tone Dial TonePrompt Tone Conﬁrm ToneFollowing is a sample ring cadence pattern conﬁguration Distinctive Ring SettingsWarm Line Supplementary Service KeysCall forward selective Block Anonymous CallsCalling Preﬁx Keys IP DialingSpeed Dialing Income Caller IDCall Conference Drop Call HoldCall Waiting call alternative Call ConferenceControl Timer Values FXS Port FXS Port Polarity Conﬁguration Ring SettingSnmp System Conﬁguration Snmp ConﬁgurationSnmp Trap Conﬁguration Snmp Community ConﬁgurationAuto Upgrade Manual Upgrade window Manual UpgradeReload Documentation Documentation link IntroductionLogout Logout window Contacting Patton for assistance Patton support headquarters in the USA Contact informationRMA numbers Warranty coverageAppendix a Compliance information CE Notice Declarations of Conformity Safety ComplianceCompliance Radio and TV Interference FCC PartAppendix B Speciﬁcations Fax and Modem Support Voice Processing signalling dependentVoice Connectivity ConnectivityOperating Environment Voice Services/FeaturesIP Services ManagementAppendix C Dial plans Complex Dial Plan Sample Dial PlansSimple Dial Plan Non-dialed Line Dial PlanSample Dial Plans Appendix D Calling Features Distinctive on Distinctive OFF Appendix E Voice prompt conﬁguration Existing voice prompt conﬁguration Accessing the voice prompt