Dukane 9136 About the remote control signal, Changing the frequency of remote control signal

Page 14

Remote control

About the remote control signal

The remote control works with the projector’s remote sensors. This projector has three remote sensors on the front, on the top, and on the back.

The sensors can be respectively turned active or inactive using the “REMOTE RECEIV.” in the SERVICE item of OPTION menu (&48). Each sensor senses the signal within the following range when the sensor is active.

The front and top sensors:

60 degrees (30 degrees to the left and right of the sensor) within 3 meters about.

The back sensor:

40 degrees (20 degrees to the left and right of the sensor) within 3 meters about.

NOTE • The remote control signal reflected in the screen or the like may be available. If it is difficult to send the signal to the sensor directly, attempt to make the signal reflect.

• The remote control uses infrared light to send

signals to the projector (Class 1 LED), so be

sure to use the remote control in an area free

from obstacles that could block the remote

control’s signal to the projector.

• The remote control may not work correctly if

30º

30º 30º

Approx.

3 m

30º Approx. 3 m

strong light (such as direct sun light) or light

from an extremely close range (such as from

an inverter fluorescent lamp) shines on the

remote sensor of the projector. Adjust the

position of projector avoiding those lights.

20º 20º Approx. 3 m

Changing the frequency of remote control signal

The accessory remote control has the choice of the mode 1 or the mode 2, in the frequency of its signal. If the remote control does not function properly, attempt to change the signal frequency. Please remember that the “REMOTE FREQ.” in SERVICE item of OPTION menu (&48) of the projector to be controlled should be set to the same mode as the remote control.

To set the mode of the remote control, slide the knob of the frequency switch inside the battery cover into the position indicated by the mode number to choose.

Back of the

remote control

Inside of

the battery cover

2

1

Frequency switch

14

Image 14
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Contents Contents of package Fastening the lens coverHOT Part namesProjector 10 9Control panel Rear panelLaser pointer &13 It is a beam outlet Remote controlBack Remote control Enter button to push down the center pointSetting up Suspended from the ceiling ArrangementOn a horizontal surface Security bar Anti-theft chain or wire Security slot Adjusting the projectors elevatorUsing the security bar and slot To loose an elevator foot Pull up the elevator knobWiht an Connecting your devicesMonitor VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply Connector of the power cord to the outletLaser pointer Remote controlInstalling the batteries Hitachi MAXELL, Part No.LR6Front and top sensors About the remote control signalChanging the frequency of remote control signal Back sensorUsing as a wired remote control Using as a simple PC mouse & keyboardTurning off the power Power on/offTurning on the power STANDBY/ON button Power indicator Power switchOperating Adjusting the volumeSelecting an input signal Temporarily muting the soundSelecting an aspect ratio Searching an input signalSelecting an input signal Using the automatic adjustment feature Adjusting the zoom and focusAdjusting the lens shift  For a video signal and s-video signalAdjusting the position Correcting the keystone distortionsUsing the magnify feature Freezing the screenTemporarily blanking the screen Enter button Using the menu functionEasy Menu Using the menu function Advanced MenuAuto Picture ModeAspect KeystoneEasy Menu Picture menu GammaPicture menu Color TempMY Memory Active IrisLOAD-1, LOAD-2, LOAD-3, LOAD-4 SAVE-1, SAVE-2, SAVE-3, SAVE-4Position Image menuOver Scan Image menu PhaseAuto Adjust SizeVideo NR Input menuProgressive 3D-YCSVideo Format Input menuComponent HdmiRGB Resolution Setup menu Setup menu Monitor OUTAudio menu Blank Using the /// buttons adjusts the menu positionScreen menu Screen menu Start UPMyScreen registration is finished Capturing error has occurred. Please try againMyScreen Message Template Using / buttons switches the mode forTemplate screen. The selected template pattern To the Template function is pressed Auto on Option menuAuto Search Lamp Time Option menuAuto OFF MY Source ServiceMY Button FanspeedLens Type GhostFilter Message Remote Receiv Factory ResetKEY Lock Remote FreqChanging the Password Using Security FeaturesInputting the Password SecurityTurning on the MyScreen Password Function Using the MyScreen Password FunctionIf you have forgotten your Password Setting the PasswordDescription Security Using the PIN Lock FunctionTurning the Password off Registering the PIN CodeTurning Off the PIN Lock Function If you have forgotten your PIN CodeTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Writing the MY Text Using the MY Text Password functionSetting the Transition Detector off Turning on the MY Text Password Displaying the MY TextPassword and the screen will return to Setup Network menuNetwork menu Projector NameMY Image To switch the image displayedPress the or ESC button on the remote control Use the / buttonsInformation Mode Closed Caption menuDisplay ChannelLamp MaintenanceCase of replacement by yourself Type number = 456-8949H Replacing the lampLamp warning LampAir filter Type number = MU05661For B holder Internal clock batteryFor a holder Inside of the projector Caring for the cabinet and remote controlOther care Caring for the lensTroubleshooting Related messagesRegarding the indicator lamps Regarding the indicator lamps Cooling fan is not operatingSignal cables are not correctly connected Electrical power cord is not pluggedPower switch is not set to the on position Signal source does not correctly workPhenomena that may be easily mistaken for machine defects Not properly adjusted Color settings are not correctly adjustedColor Space setting is not suitable Whisper function is workingSpecifications Warranty and after-serviceSpecifications Air filter MU05661Specifications 139 319 418 154 Unit mm