Dukane 9136 user manual Input menu, Progressive, Video NR, 3D-YCS, Color Space

Page 32

INPUT menu

INPUT menu

From the INPUT menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table.

Item

Description

Using the ▲/▼ buttons switches the progress mode.

TV ó FILM ó TURN OFF

	• This function is performed only for an interlaced signal at
PROGRESSIVE	the VIDEO or S-VIDEO input, and for 480i@60, 576i@50 or
PROGRESSIVE	1080i@50/60 signal at the COMPONENT or HDMI input.

•When TV or FILM is selected, the screen image will be sharp. FILM adapts to the 2-3 Pull-Down conversion system. But these may cause a certain defect (for example, jagged line) of the picture for a quick moving object. In such a case, please select TURN OFF, even though the screen image may lose the sharpness.

	Using the ▲/▼ buttons switches the noise reduction mode.
	HIGH ó MID ó LOW
VIDEO NR	• This function is performed only for the VIDEO or S-VIDEO
	input, and for 480i@60, 576i@50 or 1080i@50/60 signal at the
	COMPONENT or HDMI input.

•When this function is excessive, it may cause a certain degradation of the picture.

Using the ▲/▼ buttons switches the 3D-YCS mode.

STILL ó MOVIE ó TURN OFF

3D-YCS

• This function performs only at a VIDEO input of NTSC, and PAL.

•MOVIE is the mode for images with a lot of motions like movies, and STILL is the mode for images with few motions or completely still ones like slides.

	Using the ▲/▼ buttons switches the mode for color space.
	AUTO ó RGB ó SMPTE240 ó REC709 ó REC601
COLOR SPACE	• This item can be selected only for an RGB signal or a component
	video signal (except 480i@60, 576i@50 and SCART RGB).

•The AUTO mode automatically selects the optimum mode.

•The AUTO operation may not work well at some signals. In such a case, it might be good to select a suitable mode except AUTO.

(continued on next page)

32

Image 32

Contents Trademark acknowledgment About this manualThank you for purchasing this projector Contents Contents of package Fastening the lens coverPart names ProjectorHOT 10 9Control panel Rear panelRemote control Back Remote controlLaser pointer &13 It is a beam outlet Enter button to push down the center pointSetting up Suspended from the ceiling ArrangementOn a horizontal surface Adjusting the projectors elevator Using the security bar and slotSecurity bar Anti-theft chain or wire Security slot To loose an elevator foot Pull up the elevator knobConnecting your devices MonitorWiht an VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply Connector of the power cord to the outletRemote control Installing the batteriesLaser pointer Hitachi MAXELL, Part No.LR6About the remote control signal Changing the frequency of remote control signalFront and top sensors Back sensorUsing as a wired remote control Using as a simple PC mouse & keyboardPower on/off Turning on the powerTurning off the power STANDBY/ON button Power indicator Power switchAdjusting the volume Selecting an input signalOperating Temporarily muting the soundSelecting an aspect ratio Searching an input signalSelecting an input signal Adjusting the zoom and focus Adjusting the lens shiftUsing the automatic adjustment feature  For a video signal and s-video signalAdjusting the position Correcting the keystone distortionsUsing the magnify feature Freezing the screenTemporarily blanking the screen Enter button Using the menu functionEasy Menu Using the menu function Advanced MenuPicture Mode AspectAuto KeystoneEasy Menu Picture menu GammaPicture menu Color Temp Active Iris LOAD-1, LOAD-2, LOAD-3, LOAD-4 MY Memory SAVE-1, SAVE-2, SAVE-3, SAVE-4Position Image menuOver Scan Phase Auto AdjustImage menu SizeInput menu ProgressiveVideo NR 3D-YCSInput menu ComponentVideo Format HdmiRGB Resolution Setup menu Setup menu Monitor OUTAudio menu Blank Using the /// buttons adjusts the menu positionScreen menu Screen menu Start UPMyScreen registration is finished Capturing error has occurred. Please try againMyScreen Message Using / buttons switches the mode for Template screen. The selected template patternTemplate To the Template function is pressed Auto on Option menuAuto Search Lamp Time Option menuAuto OFF Service MY ButtonMY Source FanspeedLens Type GhostFilter Message Factory Reset KEY LockRemote Receiv Remote FreqUsing Security Features Inputting the PasswordChanging the Password SecurityUsing the MyScreen Password Function If you have forgotten your PasswordTurning on the MyScreen Password Function Setting the PasswordUsing the PIN Lock Function Turning the Password offDescription Security Registering the PIN CodeTurning Off the PIN Lock Function If you have forgotten your PIN CodeTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Writing the MY Text Using the MY Text Password functionSetting the Transition Detector off Turning on the MY Text Password Displaying the MY TextPassword and the screen will return to Setup Network menuNetwork menu Projector NameTo switch the image displayed Press the or ESC button on the remote controlMY Image Use the / buttonsInformation Closed Caption menu DisplayMode ChannelMaintenance Case of replacement by yourselfLamp Type number = 456-8949H Replacing the lampLamp warning LampAir filter Type number = MU05661For B holder Internal clock batteryFor a holder Caring for the cabinet and remote control Other careInside of the projector Caring for the lensTroubleshooting Related messagesRegarding the indicator lamps Regarding the indicator lamps Cooling fan is not operatingElectrical power cord is not plugged Power switch is not set to the on positionSignal cables are not correctly connected Signal source does not correctly workPhenomena that may be easily mistaken for machine defects Color settings are not correctly adjusted Color Space setting is not suitableNot properly adjusted Whisper function is workingWarranty and after-service SpecificationsSpecifications Air filter MU05661Specifications 139 319 418 154 Unit mm