Dukane 9136 user manual Option menu, Auto OFF, Lamp Time

Page 45

OPTION menu

OPTION menu (continued)

Item

Description

	Using the ▲/▼ buttons adjusts the time to count down to
	automatically turn the projector off.
	Long (max. 99 minutes) ó Short (min. 0 minute = DISABLE)
	When the time is set to 0, the projector is not turned off
AUTO OFF	automatically.
	When the time is set to 1 to 99, and when the passed time with no-
	signal or an unsuitable signal reaches at the set time, the projector
	lamp will be turned off.
	If one of the projector's buttons or the remote control buttons
	is pressed or one of the commands (except get commands) is
	transmitted to the CONTROL port during the corresponding time,
	projector will not be turned off.
	Please refer to the section “Turning off the power” (16).
	The lamp time is the usage time of the lamp, counted after the last
	resetting. It is shown in the OPTION menu.
	Pressing the RESET button on the remote control or the ► button
	of the projector displays a dialog.
LAMP TIME	To reset the lamp time, select the RESET using the ▲ button.
	RESET ï CANCEL

•Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp.

•For the lamp replacement, see the section “Lamp” (63, 64).

	The filter time is the usage time of the air filter, counted after the last
	resetting. It is shown in the OPTION menu.
	Pressing the RESET button on the remote control or the ► button
	of the projector displays a dialog.
FILTER TIME	To reset the filter time, select the RESET using the ▲ button.
	RESET ï CANCEL
	• Please reset the filter time only when you have cleaned or
	replaced the air filter, for a suitable indication about the air filter.
	• For the air filter cleaning, see the section “Air filter” (65).

(continued on next page)

45

Image 45

Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Fastening the lens cover Contents of packageProjector Part namesHOT 10 9Rear panel Control panelBack Remote control Remote controlLaser pointer &13 It is a beam outlet Enter button to push down the center pointSetting up Arrangement On a horizontal surfaceSuspended from the ceiling Using the security bar and slot Adjusting the projectors elevatorSecurity bar Anti-theft chain or wire Security slot To loose an elevator foot Pull up the elevator knobMonitor Connecting your devicesWiht an VCR/DVD playerAbout Plug-and-Play capability Connecting your devicesConnector of the power cord to the outlet Connecting power supplyInstalling the batteries Remote controlLaser pointer Hitachi MAXELL, Part No.LR6Changing the frequency of remote control signal About the remote control signalFront and top sensors Back sensorUsing as a simple PC mouse & keyboard Using as a wired remote controlTurning on the power Power on/offTurning off the power STANDBY/ON button Power indicator Power switchSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundSearching an input signal Selecting an input signalSelecting an aspect ratio Adjusting the lens shift Adjusting the zoom and focusUsing the automatic adjustment feature  For a video signal and s-video signalCorrecting the keystone distortions Adjusting the positionFreezing the screen Using the magnify featureTemporarily blanking the screen Using the menu function Easy MenuEnter button Advanced Menu Using the menu functionAspect Picture ModeAuto KeystoneEasy Menu Gamma Picture menuColor Temp Picture menuLOAD-1, LOAD-2, LOAD-3, LOAD-4 Active IrisMY Memory SAVE-1, SAVE-2, SAVE-3, SAVE-4Image menu Over ScanPosition Auto Adjust PhaseImage menu SizeProgressive Input menuVideo NR 3D-YCSComponent Input menuVideo Format HdmiRGB Resolution Setup menu Monitor OUT Setup menuAudio menu Using the /// buttons adjusts the menu position Screen menuBlank Start UP Screen menuCapturing error has occurred. Please try again MyScreenMyScreen registration is finished Message Template screen. The selected template pattern Using / buttons switches the mode forTemplate To the Template function is pressed Option menu Auto SearchAuto on Option menu Auto OFFLamp Time MY Button ServiceMY Source FanspeedGhost Filter MessageLens Type KEY Lock Factory ResetRemote Receiv Remote FreqInputting the Password Using Security FeaturesChanging the Password SecurityIf you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Function Setting the PasswordTurning the Password off Using the PIN Lock FunctionDescription Security Registering the PIN CodeIf you have forgotten your PIN Code Turning Off the PIN Lock FunctionUsing the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Using the MY Text Password function Setting the Transition Detector offWriting the MY Text Displaying the MY Text Turning on the MY Text PasswordPassword and the screen will return to Network menu SetupNetwork menu Name ProjectorPress the or ESC button on the remote control To switch the image displayedMY Image Use the / buttonsInformation Display Closed Caption menuMode ChannelCase of replacement by yourself MaintenanceLamp Type number = 456-8949H Replacing the lampLamp Lamp warningType number = MU05661 Air filterInternal clock battery For a holderFor B holder Other care Caring for the cabinet and remote controlInside of the projector Caring for the lensRelated messages TroubleshootingRegarding the indicator lamps Cooling fan is not operating Regarding the indicator lampsPower switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workPhenomena that may be easily mistaken for machine defects Color Space setting is not suitable Color settings are not correctly adjustedNot properly adjusted Whisper function is workingSpecifications Warranty and after-serviceSpecifications Air filter MU05661139 319 418 154 Unit mm Specifications