Dukane 9136 user manual Adjusting the position, Correcting the keystone distortions

Page 20

Operating

Adjusting the position

1. Press the POSITION button on the remote control when no menu is indicated.

The “POSITION” indication will appear on the screen.

2. Use the ▲/▼/◄/► cursor buttons to adjust the picture position. When you want to reset the operation, press the RESET button on the remote control during the operation.

To complete this operation, press the POSITION button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

PUSH ENTER

 

 

PAGE UP

 

PAGE DOWN

ESC

MENU

RESET

POSITION

AUTO

 

MAGNIFY

MY BUTTON

VOLUME

●When this function is performed on a video signal, s-video signal or component video signal, some image such as an extra-line may appear at outside of the picture.

●When this function is performing on a Video signal, S-Video signal, or component signal of 480i@60 or 576i@50 input the range of this adjustment depends on the OVER SCAN in IMAGE menu (30). It is not possible to adjust when the OVER SCAN is set to 10.

Correcting the keystone distortions

1. Press the KEYSTONE button on the remote control. A dialog will appear on the screen to aid you in correcting the distortion.

2. Use the ▲/▼ cursor buttons to select AUTO or MANUAL operation, and press the ► button to perform the following.

1)AUTO executes automatic vertical keystone correction.

2)MANUAL displays a dialog for keystone correction. Use the ◄/► cursor buttons to select the direction to correct ( or ) then use the ▲/▼ buttons for adjustment.

To close the dialog and complete this operation, press the KEYSTONE button again. Even if you don’t do anything, the dialog will automatically disappear after a few seconds.

OFF 2 -

FREEZE KEYSTONE MUTE

● The adjustable range of this function will vary among inputs. For some input, this function may not work well.

● When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, this function may not work correctly.

● When the zoom adjustment is set to the TELE (telephoto focus), this function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible.

● When the projector is placed on the level (about ±3°), this function may not work. ● When the projector is inclined to near ±30 degree or over, this function may not work well. ● When the vertical lens shift is not set fully upward (not set fully downward for the

optional lens type FL-601 only (47)), this function may not work well.

● When the horizontal lens shift is not set to the center, this function may not work well. ● This function will be unavailable when Transition Detector is on (53).

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Contents Contents of package Fastening the lens coverPart names ProjectorHOT 10 9Control panel Rear panelRemote control Back Remote controlLaser pointer &13 It is a beam outlet Enter button to push down the center pointSetting up Suspended from the ceiling ArrangementOn a horizontal surface Adjusting the projectors elevator Using the security bar and slotSecurity bar Anti-theft chain or wire Security slot To loose an elevator foot Pull up the elevator knobConnecting your devices MonitorWiht an VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply Connector of the power cord to the outletRemote control Installing the batteriesLaser pointer Hitachi MAXELL, Part No.LR6About the remote control signal Changing the frequency of remote control signalFront and top sensors Back sensorUsing as a wired remote control Using as a simple PC mouse & keyboardPower on/off Turning on the powerTurning off the power STANDBY/ON button Power indicator Power switchAdjusting the volume Selecting an input signalOperating Temporarily muting the soundSelecting an aspect ratio Searching an input signalSelecting an input signal Adjusting the zoom and focus Adjusting the lens shiftUsing the automatic adjustment feature  For a video signal and s-video signalAdjusting the position Correcting the keystone distortionsUsing the magnify feature Freezing the screenTemporarily blanking the screen Enter button Using the menu functionEasy Menu Using the menu function Advanced MenuPicture Mode AspectAuto KeystoneEasy Menu Picture menu GammaPicture menu Color TempActive Iris LOAD-1, LOAD-2, LOAD-3, LOAD-4MY Memory SAVE-1, SAVE-2, SAVE-3, SAVE-4Position Image menuOver Scan Phase Auto AdjustImage menu SizeInput menu ProgressiveVideo NR 3D-YCSInput menu ComponentVideo Format HdmiRGB Resolution Setup menu Setup menu Monitor OUTAudio menu Blank Using the /// buttons adjusts the menu positionScreen menu Screen menu Start UPMyScreen registration is finished Capturing error has occurred. Please try againMyScreen Message Using / buttons switches the mode for Template screen. The selected template patternTemplate To the Template function is pressed Auto on Option menuAuto Search Lamp Time Option menuAuto OFF Service MY ButtonMY Source FanspeedLens Type GhostFilter Message Factory Reset KEY LockRemote Receiv Remote FreqUsing Security Features Inputting the PasswordChanging the Password SecurityUsing the MyScreen Password Function If you have forgotten your PasswordTurning on the MyScreen Password Function Setting the PasswordUsing the PIN Lock Function Turning the Password offDescription Security Registering the PIN CodeTurning Off the PIN Lock Function If you have forgotten your PIN CodeTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Writing the MY Text Using the MY Text Password functionSetting the Transition Detector off Turning on the MY Text Password Displaying the MY TextPassword and the screen will return to Setup Network menuNetwork menu Projector NameTo switch the image displayed Press the or ESC button on the remote controlMY Image Use the / buttonsInformation Closed Caption menu DisplayMode ChannelMaintenance Case of replacement by yourselfLamp Type number = 456-8949H Replacing the lampLamp warning LampAir filter Type number = MU05661For B holder Internal clock batteryFor a holder Caring for the cabinet and remote control Other careInside of the projector Caring for the lensTroubleshooting Related messagesRegarding the indicator lamps Regarding the indicator lamps Cooling fan is not operatingElectrical power cord is not plugged Power switch is not set to the on positionSignal cables are not correctly connected Signal source does not correctly workPhenomena that may be easily mistaken for machine defects Color settings are not correctly adjusted Color Space setting is not suitableNot properly adjusted Whisper function is workingWarranty and after-service SpecificationsSpecifications Air filter MU05661Specifications 139 319 418 154 Unit mm
Top Page Image Contents