Dukane 9136 user manual Operating, Adjusting the volume, Temporarily muting the sound, On next

Page 17

Operating

Adjusting the volume

1. Use the VOLUME+ / VOLUME- buttons to adjust the volume.

A dialog will appear on the screen to aid you in adjusting the volume.If you do not do anything, the dialog will automatically disappear after a few seconds.

Operating

ESC MENU RESET

POSITION AUTO

MAGNIFY

MY BUTTON VOLUME

ON 1 +

OFF 2 -

FREEZE KEYSTONE MUTE

●When is selected for current picture input port, the volume adjustment is disabled. Please see AUDIO item of AUDIO menu (38).

●When the projector is in the standby mode, the volume can be adjusted if is not selected for the AUDIO OUT STANDBY of AUDIO (38).

Temporarily muting the sound

1. Press MUTE button on the remote control.

A dialog will appear on the screen indicating that you have muted the sound.

To restore the sound, press the MUTE, VOLUME+ or VOLUME- button. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

ON 1 +

OFF 2 -

FREEZE KEYSTONE MUTE

●When is selected for current picture input port, the sound is always muted. Please see AUDIO item of AUDIO menu (38).

●When the sound is muted while a signal from VIDEO(NTSC), S-VIDEO(NTSC) or COMPONENT(480i@60) port is selected, the C.C. (Closed Caption) is automatically activated if the DISPLAY item of the C.C. menu is set to AUTO and the input signal supports the C.C. feature (62).

Selecting an input signal

1. Press the INPUT button on the projector.

Each time you press the button, the projector switches its input from the current port as below.

RGB 1 RGB 2 HDMI

VIDEO S-VIDEO COMPONENT (Y, CB/PB, CR/PR)

1. Press the RGB button on the remote control to select an input port for the RGB signal.

Each time you press the button, the projector switches its RGB input from the current port as below.

LASER

INDICATOR

STANDBY/ON VIDEO

RGB

MY SOURCE/

DOC.CAMERA

RGB 1 RGB 2 HDMI

●While TURN ON is selected for AUTO SEARCH item in OPTION menu, the projector will keep checking every port sequentially till aninput signal is detected (44). If RGB button is pushed when VIDEO, S-VIDEO or COMPONENT port is selected, the projector will check RGB1 port first.

(continued on next page)

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Contents Fastening the lens cover Contents of packageProjector Part namesHOT 10 9Rear panel Control panelBack Remote control Remote controlLaser pointer &13 It is a beam outlet Enter button to push down the center pointSetting up Suspended from the ceiling ArrangementOn a horizontal surface Using the security bar and slot Adjusting the projectors elevatorSecurity bar Anti-theft chain or wire Security slot To loose an elevator foot Pull up the elevator knobMonitor Connecting your devicesWiht an VCR/DVD playerAbout Plug-and-Play capability Connecting your devicesConnector of the power cord to the outlet Connecting power supplyInstalling the batteries Remote controlLaser pointer Hitachi MAXELL, Part No.LR6Changing the frequency of remote control signal About the remote control signalFront and top sensors Back sensorUsing as a simple PC mouse & keyboard Using as a wired remote controlTurning on the power Power on/offTurning off the power STANDBY/ON button Power indicator Power switchSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundSelecting an aspect ratio Searching an input signalSelecting an input signal Adjusting the lens shift Adjusting the zoom and focusUsing the automatic adjustment feature  For a video signal and s-video signalCorrecting the keystone distortions Adjusting the positionFreezing the screen Using the magnify featureTemporarily blanking the screen Enter button Using the menu functionEasy Menu Advanced Menu Using the menu functionAspect Picture ModeAuto KeystoneEasy Menu Gamma Picture menuColor Temp Picture menuLOAD-1, LOAD-2, LOAD-3, LOAD-4 Active IrisMY Memory SAVE-1, SAVE-2, SAVE-3, SAVE-4Position Image menuOver Scan Auto Adjust PhaseImage menu SizeProgressive Input menuVideo NR 3D-YCSComponent Input menuVideo Format HdmiRGB Resolution Setup menu Monitor OUT Setup menuAudio menu Blank Using the /// buttons adjusts the menu positionScreen menu Start UP Screen menuMyScreen registration is finished Capturing error has occurred. Please try againMyScreen Message Template screen. The selected template pattern Using / buttons switches the mode forTemplate To the Template function is pressed Auto on Option menuAuto Search Lamp Time Option menuAuto OFF MY Button ServiceMY Source FanspeedLens Type GhostFilter Message KEY Lock Factory ResetRemote Receiv Remote FreqInputting the Password Using Security FeaturesChanging the Password SecurityIf you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Function Setting the PasswordTurning the Password off Using the PIN Lock FunctionDescription Security Registering the PIN CodeIf you have forgotten your PIN Code Turning Off the PIN Lock FunctionTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Writing the MY Text Using the MY Text Password functionSetting the Transition Detector off Displaying the MY Text Turning on the MY Text PasswordPassword and the screen will return to Network menu SetupNetwork menu Name ProjectorPress the or ESC button on the remote control To switch the image displayedMY Image Use the / buttonsInformation Display Closed Caption menuMode ChannelCase of replacement by yourself MaintenanceLamp Type number = 456-8949H Replacing the lampLamp Lamp warningType number = MU05661 Air filterFor B holder Internal clock batteryFor a holder Other care Caring for the cabinet and remote controlInside of the projector Caring for the lensRelated messages TroubleshootingRegarding the indicator lamps Cooling fan is not operating Regarding the indicator lampsPower switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workPhenomena that may be easily mistaken for machine defects Color Space setting is not suitable Color settings are not correctly adjustedNot properly adjusted Whisper function is workingSpecifications Warranty and after-serviceSpecifications Air filter MU05661139 319 418 154 Unit mm Specifications
Top Page Image Contents