Dukane 9136 user manual Power on/off, Turning on the power, Turning off the power

Page 16
Press the STANDBY/ON button on the projector or the remote control. The message "Power off?" will appear on the screen for about 5 seconds.

PowerContentson/off

Power on/off

Turning on the power

1. Make sure that the power cord is firmly and correctly connected to the projector and the outlet.

2. Remove the lens cover, and set the power switch to the ON position (marked “ I ”).

The POWER indicator will light up in steady orange (69). Then wait several seconds because the buttons may not function for these several seconds.

3. Press the STANDBY/ON button on the projector or the remote control.

STANDBY/ON button POWER indicator

Power switch

The projection lamp will light up and the POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in steady green.

To display the picture, select an input signal according to the section "Selecting an input signal" (17,18).

Turning off the power

1.

2. Press the STANDBY/ON button on the projector or the remote control again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete.

3. Make sure that the POWER indicator lights in steady orange, and set the power switch to the OFF position (marked “O”).

The POWER indicator will go off. Attach the lens cover.

Do not turn the projector on for 10 minutes or more after turning it off. Turning the projector on again too soon could shorten the lifetime of some consumable parts of the projector.

WARNING ►A strong light is emitted when the projector’s power is on. Do not look into the lens of the projector or look inside of the projector through any of the projector’s openings.

►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

NOTE • Turn the power on/off in right order. Please power on the projector prior to the connected devices. Power off the projector later than the connected devices.

•When the AUTO ON of the OPTION menu is set to the TURN ON, and the power was turned off by the power switch last time, turning the power switch on makes the projection lamp light on without pushing the STANDBY/ON button (44).

•Use the shutdown switch (71) only when the projector is not turned off by normal procedure.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Contents Contents of package Fastening the lens coverPart names ProjectorHOT 10 9Control panel Rear panelRemote control Back Remote controlLaser pointer &13 It is a beam outlet Enter button to push down the center pointSetting up On a horizontal surface ArrangementSuspended from the ceiling Adjusting the projectors elevator Using the security bar and slotSecurity bar Anti-theft chain or wire Security slot To loose an elevator foot Pull up the elevator knobConnecting your devices MonitorWiht an VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply Connector of the power cord to the outletRemote control Installing the batteriesLaser pointer Hitachi MAXELL, Part No.LR6About the remote control signal Changing the frequency of remote control signalFront and top sensors Back sensorUsing as a wired remote control Using as a simple PC mouse & keyboardPower on/off Turning on the powerTurning off the power STANDBY/ON button Power indicator Power switchAdjusting the volume Selecting an input signalOperating Temporarily muting the soundSelecting an input signal Searching an input signalSelecting an aspect ratio Adjusting the zoom and focus Adjusting the lens shiftUsing the automatic adjustment feature  For a video signal and s-video signalAdjusting the position Correcting the keystone distortionsUsing the magnify feature Freezing the screenTemporarily blanking the screen Easy Menu Using the menu functionEnter button Using the menu function Advanced MenuPicture Mode AspectAuto KeystoneEasy Menu Picture menu GammaPicture menu Color TempActive Iris LOAD-1, LOAD-2, LOAD-3, LOAD-4MY Memory SAVE-1, SAVE-2, SAVE-3, SAVE-4Over Scan Image menuPosition Phase Auto AdjustImage menu SizeInput menu ProgressiveVideo NR 3D-YCSInput menu ComponentVideo Format HdmiRGB Resolution Setup menu Setup menu Monitor OUTAudio menu Screen menu Using the /// buttons adjusts the menu positionBlank Screen menu Start UPMyScreen Capturing error has occurred. Please try againMyScreen registration is finished Message Using / buttons switches the mode for Template screen. The selected template patternTemplate To the Template function is pressed Auto Search Option menuAuto on Auto OFF Option menuLamp Time Service MY ButtonMY Source FanspeedFilter Message GhostLens Type Factory Reset KEY LockRemote Receiv Remote FreqUsing Security Features Inputting the PasswordChanging the Password SecurityUsing the MyScreen Password Function If you have forgotten your PasswordTurning on the MyScreen Password Function Setting the PasswordUsing the PIN Lock Function Turning the Password offDescription Security Registering the PIN CodeTurning Off the PIN Lock Function If you have forgotten your PIN CodeSetting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Setting the Transition Detector off Using the MY Text Password functionWriting the MY Text Turning on the MY Text Password Displaying the MY TextPassword and the screen will return to Setup Network menuNetwork menu Projector NameTo switch the image displayed Press the or ESC button on the remote controlMY Image Use the / buttonsInformation Closed Caption menu DisplayMode ChannelMaintenance Case of replacement by yourselfLamp Type number = 456-8949H Replacing the lampLamp warning LampAir filter Type number = MU05661For a holder Internal clock batteryFor B holder Caring for the cabinet and remote control Other careInside of the projector Caring for the lensTroubleshooting Related messagesRegarding the indicator lamps Regarding the indicator lamps Cooling fan is not operatingElectrical power cord is not plugged Power switch is not set to the on positionSignal cables are not correctly connected Signal source does not correctly workPhenomena that may be easily mistaken for machine defects Color settings are not correctly adjusted Color Space setting is not suitableNot properly adjusted Whisper function is workingWarranty and after-service SpecificationsSpecifications Air filter MU05661Specifications 139 319 418 154 Unit mm
Top Page Image Contents