Dukane 9136 user manual Lamp warning

Page 64

Maintenance

Lamp (continued)

Lamp warning

HIGH VOLTAGE

 

HIGH TEMPERATURE

HIGH PRESSURE

 

WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

►About disposal of a lamp: This product contains a mercury lamp; do not put it in a trash. Dispose of it in accordance with environmental laws.

•For lamp recycling, go to www.lamprecycle.org (in the US).

•For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada). For more information, call your dealer.

•If the lamp should break (it will make a loud bang when it does),

 

unplug the power cord from the outlet, and make sure to request a

 

replacement lamp from your local dealer. Note that shards of glass

 

could damage the projector’s internals, or cause injury during handling,

 

so please do not try to clean the projector or replace the lamp yourself.

Disconnect • If the lamp should break (it will make a loud bang when it does),

the plug

ventilate the room well, and make sure not to breathe the gas that

from the

comes out of the projector vents, or get it in your eyes or mouth.

power

outlet

• Before replacing the lamp, turn the projector off and unplug the power

 

cord, then wait at least 45 minutes for the lamp to cool sufficiently.

 

Handling the lamp while hot can cause burns, as well as damaging the

 

lamp.

• Never unscrew except the appointed (marked by an arrow) screws.

• Do not open the lamp cover while the projector is suspended from a ceiling. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

• Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

• Use only the lamp of the specified type.

• If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

• Using the lamp for long periods of time, could cause it dark, not to light up or to burst. When the pictures appear dark, or when the color tone is poor, please replace the lamp as soon as possible. Do not use old (used) lamps; this is a cause of breakage.

64

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Contents Contents of package Fastening the lens coverPart names ProjectorHOT 10 9Control panel Rear panelRemote control Back Remote controlLaser pointer &13 It is a beam outlet Enter button to push down the center pointSetting up On a horizontal surface ArrangementSuspended from the ceiling Adjusting the projectors elevator Using the security bar and slotSecurity bar Anti-theft chain or wire Security slot To loose an elevator foot Pull up the elevator knobConnecting your devices MonitorWiht an VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply Connector of the power cord to the outletRemote control Installing the batteriesLaser pointer Hitachi MAXELL, Part No.LR6About the remote control signal Changing the frequency of remote control signalFront and top sensors Back sensorUsing as a wired remote control Using as a simple PC mouse & keyboardPower on/off Turning on the powerTurning off the power STANDBY/ON button Power indicator Power switchAdjusting the volume Selecting an input signalOperating Temporarily muting the soundSelecting an input signal Searching an input signalSelecting an aspect ratio Adjusting the zoom and focus Adjusting the lens shiftUsing the automatic adjustment feature  For a video signal and s-video signalAdjusting the position Correcting the keystone distortionsUsing the magnify feature Freezing the screenTemporarily blanking the screen Easy Menu Using the menu functionEnter button Using the menu function Advanced MenuPicture Mode AspectAuto KeystoneEasy Menu Picture menu GammaPicture menu Color TempActive Iris LOAD-1, LOAD-2, LOAD-3, LOAD-4MY Memory SAVE-1, SAVE-2, SAVE-3, SAVE-4Over Scan Image menuPosition Phase Auto AdjustImage menu SizeInput menu ProgressiveVideo NR 3D-YCSInput menu ComponentVideo Format HdmiRGB Resolution Setup menu Setup menu Monitor OUTAudio menu Screen menu Using the /// buttons adjusts the menu positionBlank Screen menu Start UPMyScreen Capturing error has occurred. Please try againMyScreen registration is finished Message Using / buttons switches the mode for Template screen. The selected template patternTemplate To the Template function is pressed Auto Search Option menuAuto on Auto OFF Option menuLamp Time Service MY ButtonMY Source FanspeedFilter Message GhostLens Type Factory Reset KEY LockRemote Receiv Remote FreqUsing Security Features Inputting the PasswordChanging the Password SecurityUsing the MyScreen Password Function If you have forgotten your PasswordTurning on the MyScreen Password Function Setting the PasswordUsing the PIN Lock Function Turning the Password offDescription Security Registering the PIN CodeTurning Off the PIN Lock Function If you have forgotten your PIN CodeSetting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Setting the Transition Detector off Using the MY Text Password functionWriting the MY Text Turning on the MY Text Password Displaying the MY TextPassword and the screen will return to Setup Network menuNetwork menu Projector NameTo switch the image displayed Press the or ESC button on the remote controlMY Image Use the / buttonsInformation Closed Caption menu DisplayMode ChannelMaintenance Case of replacement by yourselfLamp Type number = 456-8949H Replacing the lampLamp warning LampAir filter Type number = MU05661For a holder Internal clock batteryFor B holder Caring for the cabinet and remote control Other careInside of the projector Caring for the lensTroubleshooting Related messagesRegarding the indicator lamps Regarding the indicator lamps Cooling fan is not operatingElectrical power cord is not plugged Power switch is not set to the on positionSignal cables are not correctly connected Signal source does not correctly workPhenomena that may be easily mistaken for machine defects Color settings are not correctly adjusted Color Space setting is not suitableNot properly adjusted Whisper function is workingWarranty and after-service SpecificationsSpecifications Air filter MU05661Specifications 139 319 418 154 Unit mm
Top Page Image Contents