Dukane 9136 user manual Network menu, Setup

Page 57

NETWORK menu

NETWORK menu

Remember that incorrect network settings on this projector may cause trouble on the network. Be sure to consult with your network administrator before connecting to an existing access point on your network.

Select “NETWORK” from the main menu to access the following functions.

Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table.

See the User’s Manual - Network Guide for details of NETWORK operation.

NOTE • If you are not utilizing SNTP (Date/Time Settings of the User’s Manual - Network Guide), then you must set the DATE AND TIME during the initial installation.

Item

Description

Selecting this item displays the SETUP menu for the network.

Use the ▲/▼ buttons to select an item, and the ► or ENTER button on the remote control to perform the item.

SETUP

 

Use the ▲/▼ buttons to turn DHCP on/off.

ON OFF

 

DHCP

Select OFF when the network does

 

(Dynamic

not have DHCP enabled.

 

Host

• When the “DHCP” setting changes to “ON”, it takes a

 

Configuration

 

Protocol)

little time to obtain IP address from DHCP server.

 

• Auto IP function will be assigned an IP address if the

 

 

 

 

projector could not obtain an IP address from server

 

 

even if DHCP is “ON”.

(continued on next page)

 

57

Image 57
Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Fastening the lens cover Contents of packageProjector Part namesHOT 10 9Rear panel Control panelBack Remote control Remote controlLaser pointer &13 It is a beam outlet Enter button to push down the center pointSetting up Arrangement On a horizontal surfaceSuspended from the ceiling Using the security bar and slot Adjusting the projectors elevatorSecurity bar Anti-theft chain or wire Security slot To loose an elevator foot Pull up the elevator knobMonitor Connecting your devicesWiht an VCR/DVD playerAbout Plug-and-Play capability Connecting your devicesConnector of the power cord to the outlet Connecting power supplyInstalling the batteries Remote controlLaser pointer Hitachi MAXELL, Part No.LR6Changing the frequency of remote control signal About the remote control signalFront and top sensors Back sensorUsing as a simple PC mouse & keyboard Using as a wired remote controlTurning on the power Power on/offTurning off the power STANDBY/ON button Power indicator Power switchSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundSearching an input signal Selecting an input signalSelecting an aspect ratio Adjusting the lens shift Adjusting the zoom and focusUsing the automatic adjustment feature  For a video signal and s-video signalCorrecting the keystone distortions Adjusting the positionFreezing the screen Using the magnify featureTemporarily blanking the screen Using the menu function Easy MenuEnter button Advanced Menu Using the menu functionAspect Picture ModeAuto KeystoneEasy Menu Gamma Picture menuColor Temp Picture menuLOAD-1, LOAD-2, LOAD-3, LOAD-4 Active IrisMY Memory SAVE-1, SAVE-2, SAVE-3, SAVE-4Image menu Over ScanPosition Auto Adjust PhaseImage menu SizeProgressive Input menuVideo NR 3D-YCSComponent Input menuVideo Format HdmiRGB Resolution Setup menu Monitor OUT Setup menuAudio menu Using the /// buttons adjusts the menu position Screen menuBlank Start UP Screen menuCapturing error has occurred. Please try again MyScreenMyScreen registration is finished Message Template screen. The selected template pattern Using / buttons switches the mode forTemplate To the Template function is pressed Option menu Auto SearchAuto on Option menu Auto OFFLamp Time MY Button ServiceMY Source FanspeedGhost Filter MessageLens Type KEY Lock Factory ResetRemote Receiv Remote FreqInputting the Password Using Security FeaturesChanging the Password SecurityIf you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Function Setting the PasswordTurning the Password off Using the PIN Lock FunctionDescription Security Registering the PIN CodeIf you have forgotten your PIN Code Turning Off the PIN Lock FunctionUsing the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Using the MY Text Password function Setting the Transition Detector offWriting the MY Text Displaying the MY Text Turning on the MY Text PasswordPassword and the screen will return to Network menu SetupNetwork menu Name ProjectorPress the or ESC button on the remote control To switch the image displayedMY Image Use the / buttonsInformation Display Closed Caption menuMode ChannelCase of replacement by yourself MaintenanceLamp Type number = 456-8949H Replacing the lampLamp Lamp warningType number = MU05661 Air filterInternal clock battery For a holderFor B holder Other care Caring for the cabinet and remote controlInside of the projector Caring for the lensRelated messages TroubleshootingRegarding the indicator lamps Cooling fan is not operating Regarding the indicator lampsPower switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workPhenomena that may be easily mistaken for machine defects Color Space setting is not suitable Color settings are not correctly adjustedNot properly adjusted Whisper function is workingSpecifications Warranty and after-serviceSpecifications Air filter MU05661139 319 418 154 Unit mm Specifications