Dukane 9136 user manual Regarding the indicator lamps, Cooling fan is not operating

Page 70

Troubleshooting

Regarding the indicator lamps (continued)

POWER TEMP LAMP

indicator indicator indicator

Description

 

 

 

The cooling fan is not operating.

Blinking

 

 

Please turn the power off, and allow the projector to

 

 

cool down at least 20 minutes. After the projector has

In Red

 

 

Blinking

Turned

sufficiently cooled down, please make confirmation

or

In Red

off

that no foreign matter has become caught in the fan,

Lighting

 

 

etc., and then turn the power on again.

In Red

 

 

 

 

If the same indication is displayed after the remedy,

 

 

 

 

 

 

please contact your dealer or service company.

 

 

 

There is a possibility that the interior portion

 

 

 

has become heated.

 

 

 

Please turn the power off, and allow the projector to

Blinking

 

 

cool down at least 20 minutes. After the projector has

 

 

sufficiently cooled down, please make confirmation of

In Red

 

 

Lighting

Turned

the following items, and then turn the power on again.

or

In Red

off

• Is there blockage of the air passage aperture?

Lighting

 

 

• Is the air filter dirty?

In Red

 

 

 

 

• Does the peripheral temperature exceed 35°C?

 

 

 

 

 

 

If the same indication is displayed after the remedy,

 

 

 

please set FANSPEED of the SERVICE item in the

 

 

 

OPTION menu to HIGH.

 

 

It is time to clean the air filter.

 

 

Please immediately turn the power off, and clean or

Lighting

Simultaneous

change the air filter referring to the section “Air Filter”.

In Green

blinking in Red

After cleaning or changing the air filter, please be sure

 

 

to reset the filter timer. After the remedy, reset the

 

 

power to on.

 

 

 

There is a possibility that the interior portion

Lighting

Alternative

has become overcooled.

Please use the unit within the usage temperature

In Green

blinking in Red

parameters (5°C to 35°C). After the treatment, reset

 

 

 

 

 

 

the power to on.

Blinking in

 

 

At least 1 “Power ON” schedule is saved to the

Green for

Turned

Turned

projector.

approx. 3

off

off

(Please refer to the User’s Manual-Network Guide:

seconds

 

 

Schedule Settings for more information.)

NOTE • When the interior portion has become overheated, for safety purposes, the power source is automatically turned off, and the indicator lamps may also be turned off. In such a case, press the “O” (off) side of the power switch, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again.

70

Page 69 Page 71
Image 70
Page 69 Page 71
Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Contents Contents of package Fastening the lens coverHOT Part namesProjector 10 9Control panel Rear panelLaser pointer &13 It is a beam outlet Remote controlBack Remote control Enter button to push down the center pointSetting up On a horizontal surface ArrangementSuspended from the ceiling Security bar Anti-theft chain or wire Security slot Adjusting the projectors elevatorUsing the security bar and slot To loose an elevator foot Pull up the elevator knobWiht an Connecting your devicesMonitor VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply Connector of the power cord to the outletLaser pointer Remote controlInstalling the batteries Hitachi MAXELL, Part No.LR6Front and top sensors About the remote control signalChanging the frequency of remote control signal Back sensorUsing as a wired remote control Using as a simple PC mouse & keyboardTurning off the power Power on/offTurning on the power STANDBY/ON button Power indicator Power switchOperating Adjusting the volumeSelecting an input signal Temporarily muting the soundSelecting an input signal Searching an input signalSelecting an aspect ratio Using the automatic adjustment feature Adjusting the zoom and focusAdjusting the lens shift  For a video signal and s-video signalAdjusting the position Correcting the keystone distortionsUsing the magnify feature Freezing the screenTemporarily blanking the screen Easy Menu Using the menu functionEnter button Using the menu function Advanced MenuAuto Picture ModeAspect KeystoneEasy Menu Picture menu GammaPicture menu Color TempMY Memory Active IrisLOAD-1, LOAD-2, LOAD-3, LOAD-4 SAVE-1, SAVE-2, SAVE-3, SAVE-4Over Scan Image menuPosition Image menu PhaseAuto Adjust SizeVideo NR Input menuProgressive 3D-YCSVideo Format Input menuComponent HdmiRGB Resolution Setup menu Setup menu Monitor OUTAudio menu Screen menu Using the /// buttons adjusts the menu positionBlank Screen menu Start UPMyScreen Capturing error has occurred. Please try againMyScreen registration is finished Message Template Using / buttons switches the mode forTemplate screen. The selected template pattern To the Template function is pressed Auto Search Option menuAuto on Auto OFF Option menuLamp Time MY Source ServiceMY Button FanspeedFilter Message GhostLens Type Remote Receiv Factory ResetKEY Lock Remote FreqChanging the Password Using Security FeaturesInputting the Password SecurityTurning on the MyScreen Password Function Using the MyScreen Password FunctionIf you have forgotten your Password Setting the PasswordDescription Security Using the PIN Lock FunctionTurning the Password off Registering the PIN CodeTurning Off the PIN Lock Function If you have forgotten your PIN CodeSetting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Setting the Transition Detector off Using the MY Text Password functionWriting the MY Text Turning on the MY Text Password Displaying the MY TextPassword and the screen will return to Setup Network menuNetwork menu Projector NameMY Image To switch the image displayedPress the or ESC button on the remote control Use the / buttonsInformation Mode Closed Caption menuDisplay ChannelLamp MaintenanceCase of replacement by yourself Type number = 456-8949H Replacing the lampLamp warning LampAir filter Type number = MU05661For a holder Internal clock batteryFor B holder Inside of the projector Caring for the cabinet and remote controlOther care Caring for the lensTroubleshooting Related messagesRegarding the indicator lamps Regarding the indicator lamps Cooling fan is not operatingSignal cables are not correctly connected Electrical power cord is not pluggedPower switch is not set to the on position Signal source does not correctly workPhenomena that may be easily mistaken for machine defects Not properly adjusted Color settings are not correctly adjustedColor Space setting is not suitable Whisper function is workingSpecifications Warranty and after-serviceSpecifications Air filter MU05661Specifications 139 319 418 154 Unit mm
Top Page Image Contents