Dukane 9136 user manual Internal clock battery, For a holder, For B holder

Page 66
Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently.

Maintenance

Internal clock battery

Consumption of the battery makes the clock not to work correctly. When the clock is wrong or it has stopped, please replace the battery according to the following procedures.

1.

2. After making sure that the projector has cooled adequately, slowly turn over the projector, so that the bottom is facing.

3. Turn the battery cover fully in the direction indicated “OPEN” using a coin or the like, and pick the cover up to remove it.

4. One of two kinds of clock battery holder, A or B shown to the right, is inside the battery cover.

For A holder:

Pry up the battery using a flathead screwdriver or the like to take it out. While prying it up, put a finger lightly on the battery since it may pop out of the holder.

For B holder:

Press the metal claw of the battery holder putting a finger lightly on the battery since it may pop out of the holder. Then the battery will come up. Remove the battery.

5. Replace the battery with a new HITACHI MAXELLL, Part No. CR2032 or CR2032H.

Slide the battery in under the plastic claw, and push it into the holder until it clicks.

6. Replace the battery cover in place, then turn it in the direction indicated “CLOSE” using such as coins, to fix.

Battery Cover

 

 

90°

 

 

 

OPEN

 

 

 

CLOSE

 

OPEN

CLOSE

OPEN

CLOSE

 

 

OPEN

CLOSE

OPEN

CLOSE

 

 

 

 

OPEN CLOSE

 

90°

 

 

NOTE • If the battery is inserted upside down in the B holder, it might be difficult to remove. If that happens, take following measures:

(1)Remove the battery cover and turn the projector's upside up.

(2)While lifting the side of the projector closer to the lens, press the metal claw of the battery holder. The battery will fall out of the holder, so be careful not to lose it.

WARNING ►Always handle the batteries with care and use them only as directed. Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire.

And also improper use may result in cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

Be sure to use only the batteries specified.

Make sure the plus and minus terminals are correctly aligned when loading a battery. If the battery is placed in the battery holder upside-down, it may be hard to remove.

Keep a battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.

Do not short circuit or solder a battery.

Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place.

If you observe battery leakage, wipe out the leakage and then replace a battery. If the leakage adheres to your body or clothes, rinse well with water immediately.

Obey the local laws on disposing the battery.

NOTE • The internal clock’s time will be reset when the battery is removed.

Please reconfigure the time via the menu or a web browser after replacing the battery.

(Date/Time Settings in the User's Manual (detailed) - Network Guide)

66

Image 66
Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Contents of package Fastening the lens coverHOT Part namesProjector 10 9Control panel Rear panelLaser pointer &13 It is a beam outlet Remote controlBack Remote control Enter button to push down the center pointSetting up Arrangement On a horizontal surfaceSuspended from the ceiling Security bar Anti-theft chain or wire Security slot Adjusting the projectors elevatorUsing the security bar and slot To loose an elevator foot Pull up the elevator knobWiht an Connecting your devicesMonitor VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply Connector of the power cord to the outletLaser pointer Remote controlInstalling the batteries Hitachi MAXELL, Part No.LR6Front and top sensors About the remote control signalChanging the frequency of remote control signal Back sensorUsing as a wired remote control Using as a simple PC mouse & keyboardTurning off the power Power on/offTurning on the power STANDBY/ON button Power indicator Power switchOperating Adjusting the volumeSelecting an input signal Temporarily muting the soundSearching an input signal Selecting an input signalSelecting an aspect ratio Using the automatic adjustment feature Adjusting the zoom and focusAdjusting the lens shift  For a video signal and s-video signalAdjusting the position Correcting the keystone distortionsUsing the magnify feature Freezing the screenTemporarily blanking the screen Using the menu function Easy MenuEnter button Using the menu function Advanced MenuAuto Picture ModeAspect KeystoneEasy Menu Picture menu GammaPicture menu Color TempMY Memory Active IrisLOAD-1, LOAD-2, LOAD-3, LOAD-4 SAVE-1, SAVE-2, SAVE-3, SAVE-4Image menu Over ScanPosition Image menu PhaseAuto Adjust SizeVideo NR Input menuProgressive 3D-YCSVideo Format Input menuComponent HdmiRGB Resolution Setup menu Setup menu Monitor OUTAudio menu Using the /// buttons adjusts the menu position Screen menuBlank Screen menu Start UPCapturing error has occurred. Please try again MyScreenMyScreen registration is finished Message Template Using / buttons switches the mode forTemplate screen. The selected template pattern To the Template function is pressed Option menu Auto SearchAuto on Option menu Auto OFFLamp Time MY Source ServiceMY Button FanspeedGhost Filter MessageLens Type Remote Receiv Factory ResetKEY Lock Remote FreqChanging the Password Using Security FeaturesInputting the Password SecurityTurning on the MyScreen Password Function Using the MyScreen Password FunctionIf you have forgotten your Password Setting the PasswordDescription Security Using the PIN Lock FunctionTurning the Password off Registering the PIN CodeTurning Off the PIN Lock Function If you have forgotten your PIN CodeUsing the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Using the MY Text Password function Setting the Transition Detector offWriting the MY Text Turning on the MY Text Password Displaying the MY TextPassword and the screen will return to Setup Network menuNetwork menu Projector NameMY Image To switch the image displayedPress the or ESC button on the remote control Use the / buttonsInformation Mode Closed Caption menuDisplay ChannelLamp MaintenanceCase of replacement by yourself Type number = 456-8949H Replacing the lampLamp warning LampAir filter Type number = MU05661Internal clock battery For a holderFor B holder Inside of the projector Caring for the cabinet and remote controlOther care Caring for the lensTroubleshooting Related messagesRegarding the indicator lamps Regarding the indicator lamps Cooling fan is not operatingSignal cables are not correctly connected Electrical power cord is not pluggedPower switch is not set to the on position Signal source does not correctly workPhenomena that may be easily mistaken for machine defects Not properly adjusted Color settings are not correctly adjustedColor Space setting is not suitable Whisper function is workingSpecifications Warranty and after-serviceSpecifications Air filter MU05661Specifications 139 319 418 154 Unit mm