Dukane 9136 Using the Transition Detector Function, Turning On the Transition Detector Function

Page 53

OPTION menu

OPTION menu (continued)

Item

Description

 

4. Using the Transition Detector Function

 

While the Transition Detector function is ON, when power switch is started to

 

supply to the projector, it might react as below.

 

• Transition Detector alarm shown below might appear on screen, if the

 

projector has been moved or re-installed.

 

• Transition Detector alarm might appear on screen, if the MIRROR setting

 

has been changed.

 

• Keystone adjustment feature has been prohibited as long as the Transition

 

Detector function is ON.

 

4.1 Turning On the Transition Detector Function

 

4.1-1 Use the ▲/▼ buttons on the SECURITY menu to

 

 

select Transition Detector and press the ► or the

 

 

 

ENTER

button to display the Transition Detector on/

 

 

off menu. Select TURN ON and the current angle

 

 

and mirror setting will be recorded.

 

• This feature may not function properly if the projector is

 

not in a stable position when TURN ON is selected.

 

4.1-2 If this function is set to TURN ON when the

 

 

vertical angle of the projector or mirror setting

 

 

at which the projector is turned on is different

 

 

than the previously recorded, the Transition

 

 

Detector Alarm will be displayed and the

 

 

projector will not display the input signal.

SECURITY

Set the Transition Detector off in the SECURITY menu to display the input signal.

If the Transition Detector ALARM is displayed for about 5 minutes, the lamp will turn

(continued)

off.

 

This function will activate only when the projector is started after the power

 

switch was turned off.

 

4.2 Setting the Transition Detector PASSWORD

 

4.2-1 Use the ▲/▼ buttons on the SECURITY menu to select Transition

 

 

Detector and press the ► or the

 

ENTER

button to display the

 

 

Transition Detector on/off menu.

 

4.2-2 Use the ▲/▼ buttons on the Transition

 

 

Detector on/off menu to select TURN ON.

 

 

The ENTER PASSWORD BOX (small) will be

 

 

displayed.

 

4.2-3 Use the ▲/▼/◄/► buttons to enter a

 

 

PASSWORD. Move the cursor to the right side of

 

 

the ENTER PASSWORD BOX (small) and press

 

 

the ► button to display the PASSWORD AGAIN

 

 

BOX, enter the same PASSWORD again.

4.2-4 Move the cursor to the right side of the PASSWORD AGAIN BOX and press the

►button to display the PASSWORD for about 20 seconds, please make note of the PASSWORD during this time.

Pressing the ENTER button on the remote control or the INPUT button on the projector will return to the Transition Detector on/off menu.

• Please do not forget your Transition Detector PASSWORD.

(continued on next page)

53

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Contents Fastening the lens cover Contents of packageProjector Part namesHOT 10 9Rear panel Control panelBack Remote control Remote controlLaser pointer &13 It is a beam outlet Enter button to push down the center pointSetting up Suspended from the ceiling ArrangementOn a horizontal surface Using the security bar and slot Adjusting the projectors elevatorSecurity bar Anti-theft chain or wire Security slot To loose an elevator foot Pull up the elevator knobMonitor Connecting your devicesWiht an VCR/DVD playerAbout Plug-and-Play capability Connecting your devicesConnector of the power cord to the outlet Connecting power supplyInstalling the batteries Remote controlLaser pointer Hitachi MAXELL, Part No.LR6Changing the frequency of remote control signal About the remote control signalFront and top sensors Back sensorUsing as a simple PC mouse & keyboard Using as a wired remote controlTurning on the power Power on/offTurning off the power STANDBY/ON button Power indicator Power switchSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundSelecting an aspect ratio Searching an input signalSelecting an input signal Adjusting the lens shift Adjusting the zoom and focusUsing the automatic adjustment feature  For a video signal and s-video signalCorrecting the keystone distortions Adjusting the positionFreezing the screen Using the magnify featureTemporarily blanking the screen Enter button Using the menu functionEasy Menu Advanced Menu Using the menu functionAspect Picture ModeAuto KeystoneEasy Menu Gamma Picture menuColor Temp Picture menuLOAD-1, LOAD-2, LOAD-3, LOAD-4 Active IrisMY Memory SAVE-1, SAVE-2, SAVE-3, SAVE-4Position Image menuOver Scan Auto Adjust PhaseImage menu SizeProgressive Input menuVideo NR 3D-YCSComponent Input menuVideo Format HdmiRGB Resolution Setup menu Monitor OUT Setup menuAudio menu Blank Using the /// buttons adjusts the menu positionScreen menu Start UP Screen menuMyScreen registration is finished Capturing error has occurred. Please try againMyScreen Message Template screen. The selected template pattern Using / buttons switches the mode forTemplate To the Template function is pressed Auto on Option menuAuto Search Lamp Time Option menuAuto OFF MY Button ServiceMY Source FanspeedLens Type GhostFilter Message KEY Lock Factory ResetRemote Receiv Remote FreqInputting the Password Using Security FeaturesChanging the Password SecurityIf you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Function Setting the PasswordTurning the Password off Using the PIN Lock FunctionDescription Security Registering the PIN CodeIf you have forgotten your PIN Code Turning Off the PIN Lock FunctionTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Writing the MY Text Using the MY Text Password functionSetting the Transition Detector off Displaying the MY Text Turning on the MY Text PasswordPassword and the screen will return to Network menu SetupNetwork menu Name ProjectorPress the or ESC button on the remote control To switch the image displayedMY Image Use the / buttonsInformation Display Closed Caption menuMode ChannelCase of replacement by yourself MaintenanceLamp Type number = 456-8949H Replacing the lampLamp Lamp warningType number = MU05661 Air filterFor B holder Internal clock batteryFor a holder Other care Caring for the cabinet and remote controlInside of the projector Caring for the lensRelated messages TroubleshootingRegarding the indicator lamps Cooling fan is not operating Regarding the indicator lampsPower switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workPhenomena that may be easily mistaken for machine defects Color Space setting is not suitable Color settings are not correctly adjustedNot properly adjusted Whisper function is workingSpecifications Warranty and after-serviceSpecifications Air filter MU05661139 319 418 154 Unit mm Specifications
Top Page Image Contents