Dukane 9136 Remote control, Laser pointer, Installing the batteries, Hitachi MAXELL, Part No.LR6

Page 13

Remote control

Remote control

Laser pointer

This remote control has a laser pointer in place of a finger or rod. The laser beam works and the LASER INDICATORlights while the LASER button is pressed.

LASER INDICATOR

LASER button

WARNING ►The laser pointer of the remote control is used in place of a finger or rod. Never look directly into the laser beam outlet or point the laser beam at other people. The laser beam can cause vision problems.

CAUTION ►Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Installing the batteries

Please insert the batteries before using the remote control. If the remote control starts to malfunction, replace the batteries. If you will not use the remote control for an extended period, remove the batteries from the remote control and store them in a safe place.

1. Slide back and remove the battery cover in the direction of the arrow.

2. Align and insert the two AA batteries

(HITACHI MAXELL, Part No.LR6

or R6P) according to their plus and minus terminals as indicated in the remote control.

3. Replace the battery cover in the direction of the arrow and snap it back into place.

WARNING ►Always handle the batteries with care and use them only as directed. Improper use may result in battery explosion, cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

•Be sure to use only the batteries specified. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

•Make sure the plus and minus terminals are correctly aligned when loading a battery.

•Keep a battery away from children and pets.

•Do not recharge, short circuit, solder or disassemble a battery.

•Do not place a battery in a fire or water. Keep batteries in a dark, cool and dry place.

•If you observe battery leakage, wipe out the leakage and then replace a battery. If the leakage adheres to your body or clothes, rinse well with water immediately.

•Obey the local laws on disposing the battery.

13

Image 13

Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Contents Fastening the lens cover Contents of packageProjector Part namesHOT 10 9Rear panel Control panelBack Remote control Remote controlLaser pointer &13 It is a beam outlet Enter button to push down the center pointSetting up On a horizontal surface ArrangementSuspended from the ceiling Using the security bar and slot Adjusting the projectors elevatorSecurity bar Anti-theft chain or wire Security slot To loose an elevator foot Pull up the elevator knobMonitor Connecting your devicesWiht an VCR/DVD playerAbout Plug-and-Play capability Connecting your devicesConnector of the power cord to the outlet Connecting power supplyInstalling the batteries Remote controlLaser pointer Hitachi MAXELL, Part No.LR6Changing the frequency of remote control signal About the remote control signalFront and top sensors Back sensorUsing as a simple PC mouse & keyboard Using as a wired remote controlTurning on the power Power on/offTurning off the power STANDBY/ON button Power indicator Power switchSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundSelecting an input signal Searching an input signalSelecting an aspect ratio Adjusting the lens shift Adjusting the zoom and focusUsing the automatic adjustment feature  For a video signal and s-video signalCorrecting the keystone distortions Adjusting the positionFreezing the screen Using the magnify featureTemporarily blanking the screen Easy Menu Using the menu functionEnter button Advanced Menu Using the menu functionAspect Picture ModeAuto KeystoneEasy Menu Gamma Picture menuColor Temp Picture menuLOAD-1, LOAD-2, LOAD-3, LOAD-4 Active IrisMY Memory SAVE-1, SAVE-2, SAVE-3, SAVE-4Over Scan Image menuPosition Auto Adjust PhaseImage menu SizeProgressive Input menuVideo NR 3D-YCSComponent Input menuVideo Format HdmiRGB Resolution Setup menu Monitor OUT Setup menuAudio menu Screen menu Using the /// buttons adjusts the menu positionBlank Start UP Screen menuMyScreen Capturing error has occurred. Please try againMyScreen registration is finished Message Template screen. The selected template pattern Using / buttons switches the mode forTemplate To the Template function is pressed Auto Search Option menuAuto on Auto OFF Option menuLamp Time MY Button ServiceMY Source FanspeedFilter Message GhostLens Type KEY Lock Factory ResetRemote Receiv Remote FreqInputting the Password Using Security FeaturesChanging the Password SecurityIf you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Function Setting the PasswordTurning the Password off Using the PIN Lock FunctionDescription Security Registering the PIN CodeIf you have forgotten your PIN Code Turning Off the PIN Lock FunctionSetting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Setting the Transition Detector off Using the MY Text Password functionWriting the MY Text Displaying the MY Text Turning on the MY Text PasswordPassword and the screen will return to Network menu SetupNetwork menu Name ProjectorPress the or ESC button on the remote control To switch the image displayedMY Image Use the / buttonsInformation Display Closed Caption menuMode ChannelCase of replacement by yourself MaintenanceLamp Type number = 456-8949H Replacing the lampLamp Lamp warningType number = MU05661 Air filterFor a holder Internal clock batteryFor B holder Other care Caring for the cabinet and remote controlInside of the projector Caring for the lensRelated messages TroubleshootingRegarding the indicator lamps Cooling fan is not operating Regarding the indicator lampsPower switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workPhenomena that may be easily mistaken for machine defects Color Space setting is not suitable Color settings are not correctly adjustedNot properly adjusted Whisper function is workingSpecifications Warranty and after-serviceSpecifications Air filter MU05661139 319 418 154 Unit mm Specifications