Christie Digital Systems DHD800 user manual Terminals of Projector, Replacement of Terminal

Page 21

Installation

Terminals of Projector

The projector has two replaceable Interface board slots. The projector's functions can be extended by installing the optional interface boards into the terminal slots. For the Optional Interface Boards, contact sales dealer where you purchased the projector.

INPUT/OUTPUT

TERMINALS

2 TERMINAL SLOTS (Factory set)

Replacement of Terminal

Note:

•In the event of replacement of interface board, turn off the projector, press the Main On/Off Switch to Off and unplug the AC power cord from the AC outlet.

1Remove 2 Screws from an interface board.

2Pull out the interface board.

3Replace the interface board. Insert a new interface board along Guide to ﬁt Plug into Socket.

4Tighten screws to secure the interface board.

NOTES ON ORDERING OR USING OPTIONAL INTERFACE BOARD

When ordering or using Optional Interface Board, contact your sales dealer. When contacting the sales dealer, tell the Option Control Number (Op.cont.No.) in the menu that is located on the bottom of the information menu.

(See page 29)

Screws

Guide

Socket

Plug

Figure shows Dual SDI Board

	DHD800 User Manual	19
	020-000244-01 Rev.1 (08-2010)	19
	020-000244-01 Rev.1 (08-2010)

Image 21

Contents DHD800 Page User’s Manual Features and Design Table of Contents For EU Users To The OwnerSafety Instructions Air Circulation Positioning Precautions Installing the Projector in Proper DirectionsMoving the Projector AC Power Cord for the United States and Canada ComplianceCanadian Radio Interference Regulations Part Names and Functions FrontBack USB Connector Series B Terminals and ConnectorsD-sub 15-PIN Input Terminal LAN portSide Control Side Control and IndicatorsIndicators Remote Control Remote Control Battery Installation Remote Control Receivers and Operating RangeWired Remote Control Remote Control Code Remote Control Code Pressing Image ADJ ButtonNumber of Times Lens Installation InstallationPicture Level and Pitch Adjustment Positioning ProjectorWhen the lens is shifted to top Lens Shift AdjustmentWhen the lens is shifted to bottom When the lens is shifted to rightmostTerminals of Projector Replacement of TerminalConnecting to Computer Cables used for connectionTerminals of the projector Connecting to Video Equipment Monitor Out Signal TableProjector To loosen the cable tie Attaching the Cable TieConnecting the AC Power Cord For the U.S.A. and CanadaFor Continental Europe Basic Operation What is PIN code?Turning On the Projector Enter a PIN codeTurning Off the Projector How to Operate the On-Screen Menu Remote ControlOn-Screen Menu Menu Bar Operating with Projector Control Information Menu InformationOperating with Remote Control Shutter button Timer buttonFilter button Image ADJ. buttonInput Selection Remote Control OperationInput Side Control OperationComputer Input Source Selection When Selecting the Input 1 with DVI/D-sub 15 terminalsMenu Operation Input MenuVideo Input Source Selection RGB AV HdcpPb/Cb, Pr/Cr Computer System Selection Computer InputAutomatic Multi-Scan System Selecting Computer System ManuallyTo store the adjusted parameters Auto PC AdjustmentPC Adjust Menu Direct OperationManual PC Adjustment Mode free ResetTo clear the adjusted data To store the adjusted dataStandard Real Dynamic Image1 Image SEL. button Image Level SelectionStandard ImageScreen Menu Screen Size AdjustmentCeiling KeystoneRear Digital zoom +Video System Selection Video InputVideo Jack or S-Video Jack Pb/Cb, Pr/Cr JacksStandard Cinema Dynamic Image1 Image SEL. button Natural Wide Keystone Image Adjust Menu Image AdjustmentPointer Mode Picture ImageMenu Color MList Color M Menu Color PaletteOffset Red/Green/Blue White balance Red/Green/BlueSharpness GammaSetting SettingBackground Lamp modeLamp control Lamp life controlPicture in Picture Color matching Edge blendingAdvanced color matching DynamicBlackLogo Hdmi setupLogo select CaptureChange the Logo PIN code lock setting Enter a Logo PIN codeChange the Logo PIN code To change the code for the remote control Remote controlTo reset the code for the remote control Filter controlOn start Power managementSecurity Key lock PIN code lockSecurity Change the PIN Code Change the PIN Code Lock settingProtection ShutterEffect Release keyVideo delay control Closed captionFrame lock Filter counter Filter replacement iconTest pattern Factory defaultFilter Instructions Maintenance and CareService Parts No 350 Reset the filter counter and the scroll counter p.66Resetting the Scroll Counter Resetting the Filter CounterFilter counter Scroll counterLamp Mode Changeover Lamp 1/2 Replace IndicatorsLamp Management Lamp Status DisplayLamp Replacement IndicatorsLamp 1 / 2 Replace indicators Lamp Handling Precautions Optional Color Wheel Installation Cleaning the Projector Cabinet Cleaning the Projection LensThen check the matters below Lamp indicator lights on and other indicators blinkAppendix TroubleshootingAppendix Power is turned off Menu Tree Information Image AdjustComputer Input/Video Input NetworkSystem PC AdjustImage Select ScreenSetting Projector is operating normally Indicators and Projector ConditionLamp Replace 1 Projector is detecting abnormal conditionFilter replacement icon ON-SCREEN Resolution Compatible Computer SpecificationsFreq.kHz Freq.Hz Display30.000 List of Picture in Picture Supported Signal Format for Optional BoardTechnical Specifications Optional Parts Configurations of Terminals InputOutput PIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Unit inch mm DimensionsEdge blending How to adjust multiple screensColor matching Page Page Corporate offices