Christie Digital Systems DHD800 user manual Moving the Projector

Page 10

Safety Instructions

Moving the Projector

Retract the adjustable feet to prevent damage

How to move the projector by one person

to lens and cabinet. For safety, holding the

 

projector on both sides by 2 or more people is

 

recommended to move the projector because

 

the projector is heavy. When moving the

 

projector by one person from necessity, hold

 

the handle carefully. Moving it improperly may

 

result in damage of cabinet or person's injury.

 

CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR

–Do not drop or bump the projector, otherwise damages or malfunctions may result.

–When carrying the projector, use a suitable carrying case.

–Do not transport the projector by courier or any other transport service in an unsuitable transport case. This may cause damage to the projector. For information about transporting the projector by courier or any other transport service, consult your dealer.

–Do not put the projector in a case before it is cooled enough.

–Do not transport the projector with a replacement lens installed.

When moving the projector by one person, grip handles and carry it with lens side up. Then, lay it down on the correct position.

8

DHD800 User Manual

020-000244-01 Rev.1 (08-2010)

 

Image 10
Contents DHD800 Page User’s Manual Features and Design Table of Contents To The Owner For EU UsersSafety Instructions Air Circulation Installing the Projector in Proper Directions Positioning PrecautionsMoving the Projector Compliance AC Power Cord for the United States and CanadaCanadian Radio Interference Regulations Front Part Names and FunctionsBack D-sub 15-PIN Input Terminal Terminals and ConnectorsUSB Connector Series B LAN portSide Control and Indicators Side ControlIndicators Remote Control Remote Control Receivers and Operating Range Remote Control Battery InstallationWired Remote Control Remote Control Code Pressing Image ADJ Button Remote Control CodeNumber of Times Picture Level and Pitch Adjustment InstallationLens Installation Positioning ProjectorWhen the lens is shifted to bottom Lens Shift AdjustmentWhen the lens is shifted to top When the lens is shifted to rightmostReplacement of Terminal Terminals of ProjectorCables used for connection Connecting to ComputerTerminals of the projector Monitor Out Signal Table Connecting to Video EquipmentProjector Attaching the Cable Tie To loosen the cable tieFor the U.S.A. and Canada Connecting the AC Power CordFor Continental Europe Turning On the Projector What is PIN code?Basic Operation Enter a PIN codeTurning Off the Projector Remote Control How to Operate the On-Screen MenuOn-Screen Menu Menu Bar Operating with Projector Control Information Information MenuOperating with Remote Control Filter button Timer buttonShutter button Image ADJ. buttonInput Remote Control OperationInput Selection Side Control OperationMenu Operation When Selecting the Input 1 with DVI/D-sub 15 terminalsComputer Input Source Selection Input MenuRGB AV Hdcp Video Input Source SelectionPb/Cb, Pr/Cr Automatic Multi-Scan System Computer InputComputer System Selection Selecting Computer System ManuallyPC Adjust Menu Auto PC AdjustmentTo store the adjusted parameters Direct OperationManual PC Adjustment To clear the adjusted data ResetMode free To store the adjusted dataStandard Image Level SelectionStandard Real Dynamic Image1 Image SEL. button ImageScreen Size Adjustment Screen MenuRear KeystoneCeiling Digital zoom +Video Jack or S-Video Jack Video InputVideo System Selection Pb/Cb, Pr/Cr JacksStandard Cinema Dynamic Image1 Image SEL. button Natural Wide Keystone Pointer Mode Image AdjustmentImage Adjust Menu Picture ImageList Color M Menu Color MMenu Color PaletteSharpness White balance Red/Green/BlueOffset Red/Green/Blue GammaSetting SettingLamp control Lamp modeBackground Lamp life controlPicture in Picture Edge blending Color matchingDynamicBlack Advanced color matchingLogo select Hdmi setupLogo CaptureEnter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code To reset the code for the remote control Remote controlTo change the code for the remote control Filter controlPower management On startPIN code lock Security Key lockSecurity Change the PIN Code Lock setting Change the PIN CodeEffect ShutterProtection Release keyClosed caption Video delay controlFrame lock Filter replacement icon Filter counterFactory default Test patternMaintenance and Care Filter InstructionsReset the filter counter and the scroll counter p.66 Service Parts No 350Filter counter Resetting the Filter CounterResetting the Scroll Counter Scroll counterLamp Management Lamp 1/2 Replace IndicatorsLamp Mode Changeover Lamp Status DisplayIndicators Lamp ReplacementLamp 1 / 2 Replace indicators Lamp Handling Precautions Optional Color Wheel Installation Cleaning the Projection Lens Cleaning the Projector CabinetLamp indicator lights on and other indicators blink Then check the matters belowTroubleshooting AppendixAppendix Power is turned off Computer Input/Video Input Information Image AdjustMenu Tree NetworkImage Select PC AdjustSystem ScreenSetting Indicators and Projector Condition Projector is operating normallyProjector is detecting abnormal condition Lamp Replace 1Filter replacement icon Freq.kHz Freq.Hz Compatible Computer SpecificationsON-SCREEN Resolution Display30.000 Supported Signal Format for Optional Board List of Picture in PictureTechnical Specifications Optional Parts Input Configurations of TerminalsOutput PIN Code Lock No PIN Code Number MemoLogo PIN Code Lock No Dimensions Unit inch mmHow to adjust multiple screens Edge blendingColor matching Page Page Corporate offices