Christie Digital Systems DHD800 user manual Lamp Handling Precautions

Page 71

Maintenance and Care

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the following information to the dealer.

L

Model No. of your projector

:

DHD800

L

Replacement Lamp Type No.

:

003-120577-01

 

 

 

(Service Parts No. 610 350 6814)

LAMP HANDLING PRECAUTIONS

This projector uses a high-pressure lamp which must be handled carefully and properly.

Improper handling may result in accidents, injury, or create a fire hazard.

L Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps.

L If the projector indicates that the lamp should be replaced, i.e., if the LAMP 1/2 REPLACE indicators light up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP 1/2 REPLACE indicators lighted may increase the risk of lamp explosion.

L Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service center for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

DHD800 User Manual

69

020-000244-01 Rev.1 (08-2010)

 

Image 71
Contents DHD800 Page User’s Manual Features and Design Table of Contents For EU Users To The OwnerSafety Instructions Air Circulation Positioning Precautions Installing the Projector in Proper DirectionsMoving the Projector Canadian Radio Interference Regulations AC Power Cord for the United States and CanadaCompliance Back Part Names and FunctionsFront LAN port Terminals and ConnectorsUSB Connector Series B D-sub 15-PIN Input TerminalSide Control Side Control and IndicatorsIndicators Remote Control Wired Remote Control Remote Control Battery InstallationRemote Control Receivers and Operating Range Number of Times Remote Control CodeRemote Control Code Pressing Image ADJ Button Positioning Projector InstallationLens Installation Picture Level and Pitch AdjustmentWhen the lens is shifted to rightmost Lens Shift AdjustmentWhen the lens is shifted to top When the lens is shifted to bottomTerminals of Projector Replacement of TerminalTerminals of the projector Connecting to ComputerCables used for connection Projector Connecting to Video EquipmentMonitor Out Signal Table To loosen the cable tie Attaching the Cable TieFor Continental Europe Connecting the AC Power CordFor the U.S.A. and Canada Enter a PIN code What is PIN code?Basic Operation Turning On the ProjectorTurning Off the Projector On-Screen Menu How to Operate the On-Screen MenuRemote Control Menu Bar Operating with Projector Control Information Menu InformationOperating with Remote Control Image ADJ. button Timer buttonShutter button Filter buttonSide Control Operation Remote Control OperationInput Selection InputInput Menu When Selecting the Input 1 with DVI/D-sub 15 terminalsComputer Input Source Selection Menu OperationPb/Cb, Pr/Cr Video Input Source SelectionRGB AV Hdcp Selecting Computer System Manually Computer InputComputer System Selection Automatic Multi-Scan SystemDirect Operation Auto PC AdjustmentTo store the adjusted parameters PC Adjust MenuManual PC Adjustment To store the adjusted data ResetMode free To clear the adjusted dataImage Image Level SelectionStandard Real Dynamic Image1 Image SEL. button StandardScreen Menu Screen Size AdjustmentDigital zoom + KeystoneCeiling RearPb/Cb, Pr/Cr Jacks Video InputVideo System Selection Video Jack or S-Video JackStandard Cinema Dynamic Image1 Image SEL. button Natural Wide Keystone Picture Image Image AdjustmentImage Adjust Menu Pointer ModeColor Palette Color MMenu List Color M MenuGamma White balance Red/Green/BlueOffset Red/Green/Blue SharpnessSetting SettingLamp life control Lamp modeBackground Lamp controlPicture in Picture Color matching Edge blendingAdvanced color matching DynamicBlackCapture Hdmi setupLogo Logo selectChange the Logo PIN code Change the Logo PIN code lock settingEnter a Logo PIN code Filter control Remote controlTo change the code for the remote control To reset the code for the remote controlOn start Power managementSecurity Security Key lockPIN code lock Change the PIN Code Change the PIN Code Lock settingRelease key ShutterProtection EffectFrame lock Video delay controlClosed caption Filter counter Filter replacement iconTest pattern Factory defaultFilter Instructions Maintenance and CareService Parts No 350 Reset the filter counter and the scroll counter p.66Scroll counter Resetting the Filter CounterResetting the Scroll Counter Filter counterLamp Status Display Lamp 1/2 Replace IndicatorsLamp Mode Changeover Lamp ManagementLamp 1 / 2 Replace indicators Lamp ReplacementIndicators Lamp Handling Precautions Optional Color Wheel Installation Cleaning the Projector Cabinet Cleaning the Projection LensThen check the matters below Lamp indicator lights on and other indicators blinkAppendix TroubleshootingAppendix Power is turned off Network Information Image AdjustMenu Tree Computer Input/Video InputScreen PC AdjustSystem Image SelectSetting Projector is operating normally Indicators and Projector ConditionLamp Replace 1 Projector is detecting abnormal conditionFilter replacement icon Display Compatible Computer SpecificationsON-SCREEN Resolution Freq.kHz Freq.Hz30.000 List of Picture in Picture Supported Signal Format for Optional BoardTechnical Specifications Optional Parts Output Configurations of TerminalsInput Logo PIN Code Lock No PIN Code Number MemoPIN Code Lock No Unit inch mm DimensionsEdge blending How to adjust multiple screensColor matching Page Page Corporate offices