Christie Digital Systems DHD800 user manual Optional Color Wheel Installation

Page 72

Maintenance and Care

Optional Color Wheel Installation

The projector comes with the high brightness color wheels installed. Additional rich color reproduction color wheels are supplied. To replace the color wheels, refer to the following steps.

1Turn off the projector, press the Main On/Off Switch to Off and unplug the AC power cord from the AC outlet. Let the projector cool for at least 45 minutes.

2Loosen a screw on the Lamp Cover. Slide and open the Lamp Cover. (See the right figure.)

3Loosen three screws and pull out the color wheel to be replaced by grasping handle.

4Replace the color wheel with a new one and tighten three screws. Make sure the color wheels are set properly.

5Put the Lamp Cover back and tighten a screw.

Note:

•Wait until the lamp house and the color wheel cool off.

•Make sure to install the same type of two color wheels at the same time. When different types of color wheels are installed, ‘Non-matching color wheels!‘ message appears on the screen.

SCREW

LAMP

COVER

COLOR WHEELS

SCREWS

Allow the projector to cool, for at least 45 minutes before you open Lamp Cover. The inside of the projector can become very hot.

	70	DHD800 User Manual
	70	020-000244-01 Rev.1 (08-2010)
		020-000244-01 Rev.1 (08-2010)

Image 72

Contents DHD800 Page User’s Manual Features and Design Table of Contents To The Owner For EU UsersSafety Instructions Air Circulation Installing the Projector in Proper Directions Positioning PrecautionsMoving the Projector AC Power Cord for the United States and Canada ComplianceCanadian Radio Interference Regulations Part Names and Functions FrontBack Terminals and Connectors USB Connector Series BD-sub 15-PIN Input Terminal LAN portSide Control and Indicators Side ControlIndicators Remote Control Remote Control Battery Installation Remote Control Receivers and Operating RangeWired Remote Control Remote Control Code Remote Control Code Pressing Image ADJ ButtonNumber of Times Installation Lens InstallationPicture Level and Pitch Adjustment Positioning ProjectorLens Shift Adjustment When the lens is shifted to topWhen the lens is shifted to bottom When the lens is shifted to rightmostReplacement of Terminal Terminals of ProjectorConnecting to Computer Cables used for connectionTerminals of the projector Connecting to Video Equipment Monitor Out Signal TableProjector Attaching the Cable Tie To loosen the cable tieConnecting the AC Power Cord For the U.S.A. and CanadaFor Continental Europe What is PIN code? Basic OperationTurning On the Projector Enter a PIN codeTurning Off the Projector How to Operate the On-Screen Menu Remote ControlOn-Screen Menu Menu Bar Operating with Projector Control Information Information MenuOperating with Remote Control Timer button Shutter buttonFilter button Image ADJ. buttonRemote Control Operation Input SelectionInput Side Control OperationWhen Selecting the Input 1 with DVI/D-sub 15 terminals Computer Input Source SelectionMenu Operation Input MenuVideo Input Source Selection RGB AV HdcpPb/Cb, Pr/Cr Computer Input Computer System SelectionAutomatic Multi-Scan System Selecting Computer System ManuallyAuto PC Adjustment To store the adjusted parametersPC Adjust Menu Direct OperationManual PC Adjustment Reset Mode freeTo clear the adjusted data To store the adjusted dataImage Level Selection Standard Real Dynamic Image1 Image SEL. buttonStandard ImageScreen Size Adjustment Screen MenuKeystone CeilingRear Digital zoom +Video Input Video System SelectionVideo Jack or S-Video Jack Pb/Cb, Pr/Cr JacksStandard Cinema Dynamic Image1 Image SEL. button Natural Wide Keystone Image Adjustment Image Adjust MenuPointer Mode Picture ImageColor M MenuList Color M Menu Color PaletteWhite balance Red/Green/Blue Offset Red/Green/BlueSharpness GammaSetting SettingLamp mode BackgroundLamp control Lamp life controlPicture in Picture Edge blending Color matchingDynamicBlack Advanced color matchingHdmi setup LogoLogo select CaptureChange the Logo PIN code lock setting Enter a Logo PIN codeChange the Logo PIN code Remote control To change the code for the remote controlTo reset the code for the remote control Filter controlPower management On startSecurity Key lock PIN code lockSecurity Change the PIN Code Lock setting Change the PIN CodeShutter ProtectionEffect Release keyVideo delay control Closed captionFrame lock Filter replacement icon Filter counterFactory default Test patternMaintenance and Care Filter InstructionsReset the filter counter and the scroll counter p.66 Service Parts No 350Resetting the Filter Counter Resetting the Scroll CounterFilter counter Scroll counterLamp 1/2 Replace Indicators Lamp Mode ChangeoverLamp Management Lamp Status DisplayLamp Replacement IndicatorsLamp 1 / 2 Replace indicators Lamp Handling Precautions Optional Color Wheel Installation Cleaning the Projection Lens Cleaning the Projector CabinetLamp indicator lights on and other indicators blink Then check the matters belowTroubleshooting AppendixAppendix Power is turned off Information Image Adjust Menu TreeComputer Input/Video Input NetworkPC Adjust SystemImage Select ScreenSetting Indicators and Projector Condition Projector is operating normallyProjector is detecting abnormal condition Lamp Replace 1Filter replacement icon Compatible Computer Specifications ON-SCREEN ResolutionFreq.kHz Freq.Hz Display30.000 Supported Signal Format for Optional Board List of Picture in PictureTechnical Specifications Optional Parts Configurations of Terminals InputOutput PIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Dimensions Unit inch mmHow to adjust multiple screens Edge blendingColor matching Page Page Corporate offices