Christie Digital Systems DHD800 Video Input, Video System Selection, Video Jack or S-Video Jack

Page 44

Video Input

Video System Selection

1Press the MENU button to display the On-Screen Menu. Use the Point buttons to move the red frame pointer to the AV System Menu icon.

2Use the Point 54 buttons to move the red arrow pointer to the desired system and then press the SELECT button.

Video Jack or S-Video Jack

Auto

The projector automatically detects an incoming video system, and adjusts itself to optimize its performance.

PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N

If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N.

AV SYSTEM MENU (VIDEO OR S-VIDEO)

AV System Menu icon

The selected system is displayed

Move the pointer to the desired system and press the SELECT button.

Y, Pb/Cb, Pr/Cr Jacks

Auto

The projector automatically detects an incoming video signal, and adjusts itself to optimize its performance.

When the Video System is 1035i or 1080i, select the system manually.

COMPONENT VIDEO SIGNAL FORMAT

If the projector cannot reproduce proper video image, select a specific component video signal format from among 480i, 575i, 480p, 575p, 720p, 1035i, 1080p, and 1080i.

Note:

•The AV System menu cannot be selected when selecting RGB(Scart).

AV SYSTEM MENU (COMPONENT VIDEO)

AV System Menu icon

The selected system is displayed.

Move the pointer to the desired system and press the SELECT button.

	42	DHD800 User Manual
	42	020-000244-01 Rev.1 (08-2010)
		020-000244-01 Rev.1 (08-2010)

Image 44

Contents DHD800 Page User’s Manual Features and Design Table of Contents To The Owner For EU UsersSafety Instructions Air Circulation Installing the Projector in Proper Directions Positioning PrecautionsMoving the Projector Canadian Radio Interference Regulations AC Power Cord for the United States and CanadaCompliance Back Part Names and FunctionsFront Terminals and Connectors USB Connector Series BD-sub 15-PIN Input Terminal LAN portSide Control and Indicators Side ControlIndicators Remote Control Wired Remote Control Remote Control Battery InstallationRemote Control Receivers and Operating Range Number of Times Remote Control CodeRemote Control Code Pressing Image ADJ Button Installation Lens InstallationPicture Level and Pitch Adjustment Positioning ProjectorLens Shift Adjustment When the lens is shifted to topWhen the lens is shifted to bottom When the lens is shifted to rightmostReplacement of Terminal Terminals of ProjectorTerminals of the projector Connecting to ComputerCables used for connection Projector Connecting to Video EquipmentMonitor Out Signal Table Attaching the Cable Tie To loosen the cable tieFor Continental Europe Connecting the AC Power CordFor the U.S.A. and Canada What is PIN code? Basic OperationTurning On the Projector Enter a PIN codeTurning Off the Projector On-Screen Menu How to Operate the On-Screen MenuRemote Control Menu Bar Operating with Projector Control Information Information MenuOperating with Remote Control Timer button Shutter buttonFilter button Image ADJ. buttonRemote Control Operation Input SelectionInput Side Control OperationWhen Selecting the Input 1 with DVI/D-sub 15 terminals Computer Input Source SelectionMenu Operation Input MenuPb/Cb, Pr/Cr Video Input Source SelectionRGB AV Hdcp Computer Input Computer System SelectionAutomatic Multi-Scan System Selecting Computer System ManuallyAuto PC Adjustment To store the adjusted parametersPC Adjust Menu Direct OperationManual PC Adjustment Reset Mode freeTo clear the adjusted data To store the adjusted dataImage Level Selection Standard Real Dynamic Image1 Image SEL. buttonStandard ImageScreen Size Adjustment Screen MenuKeystone CeilingRear Digital zoom +Video Input Video System SelectionVideo Jack or S-Video Jack Pb/Cb, Pr/Cr JacksStandard Cinema Dynamic Image1 Image SEL. button Natural Wide Keystone Image Adjustment Image Adjust MenuPointer Mode Picture ImageColor M MenuList Color M Menu Color PaletteWhite balance Red/Green/Blue Offset Red/Green/BlueSharpness GammaSetting SettingLamp mode BackgroundLamp control Lamp life controlPicture in Picture Edge blending Color matchingDynamicBlack Advanced color matchingHdmi setup LogoLogo select CaptureChange the Logo PIN code Change the Logo PIN code lock settingEnter a Logo PIN code Remote control To change the code for the remote controlTo reset the code for the remote control Filter controlPower management On startSecurity Security Key lockPIN code lock Change the PIN Code Lock setting Change the PIN CodeShutter ProtectionEffect Release keyFrame lock Video delay controlClosed caption Filter replacement icon Filter counterFactory default Test patternMaintenance and Care Filter InstructionsReset the filter counter and the scroll counter p.66 Service Parts No 350Resetting the Filter Counter Resetting the Scroll CounterFilter counter Scroll counterLamp 1/2 Replace Indicators Lamp Mode ChangeoverLamp Management Lamp Status DisplayLamp 1 / 2 Replace indicators Lamp ReplacementIndicators Lamp Handling Precautions Optional Color Wheel Installation Cleaning the Projection Lens Cleaning the Projector CabinetLamp indicator lights on and other indicators blink Then check the matters belowTroubleshooting AppendixAppendix Power is turned off Information Image Adjust Menu TreeComputer Input/Video Input NetworkPC Adjust SystemImage Select ScreenSetting Indicators and Projector Condition Projector is operating normallyProjector is detecting abnormal condition Lamp Replace 1Filter replacement icon Compatible Computer Specifications ON-SCREEN ResolutionFreq.kHz Freq.Hz Display30.000 Supported Signal Format for Optional Board List of Picture in PictureTechnical Specifications Optional Parts Output Configurations of TerminalsInput Logo PIN Code Lock No PIN Code Number MemoPIN Code Lock No Dimensions Unit inch mmHow to adjust multiple screens Edge blendingColor matching Page Page Corporate offices