Christie Digital Systems DHD800 user manual How to Operate the On-Screen Menu, Remote Control

Page 28

Basic Operation

How to Operate the On-Screen Menu

The projector can be adjusted or set via the On-Screen	Side Control
Menu. For each adjustment and setting procedure, refer
to the respective sections in this manual.

1Press the MENU button on the side control or the remote control to display the On-Screen Menu.

2Use the Point buttons to select a Menu icon. Use the Point 54 buttons to select an item in the selected menu.

3Press the SELECT button to show the item data. Use the Point buttons to adjust the values.

To close the On-Screen Menu, press the MENU button again.

Note:

•The selected item is not active until the SELECT button is pressed.

MENU button

POINT buttons

SELECT button

Remote Control

MENU button

POINT buttons

SELECT button

On-Screen Menu

		Menu icon
	Menu bar
	Pointer (red frame )	Pointer
	Pointer (red frame )	(red frame )
		(red frame )
	Press the Point 54 buttons
	to move the pointer.
	Item
	SELECT
	button

Press the SELECT button here to display previous items.

Item data

Press the Point buttons to adjust the value.

Press the SELECT button here to display next items.

	26	DHD800 User Manual
	26	020-000244-01 Rev.1 (08-2010)
		020-000244-01 Rev.1 (08-2010)

Image 28

Contents DHD800 Page User’s Manual Features and Design Table of Contents To The Owner For EU UsersSafety Instructions Air Circulation Installing the Projector in Proper Directions Positioning PrecautionsMoving the Projector Compliance AC Power Cord for the United States and CanadaCanadian Radio Interference Regulations Front Part Names and FunctionsBack Terminals and Connectors USB Connector Series BD-sub 15-PIN Input Terminal LAN portSide Control and Indicators Side ControlIndicators Remote Control Remote Control Receivers and Operating Range Remote Control Battery InstallationWired Remote Control Remote Control Code Pressing Image ADJ Button Remote Control CodeNumber of Times Installation Lens InstallationPicture Level and Pitch Adjustment Positioning ProjectorLens Shift Adjustment When the lens is shifted to topWhen the lens is shifted to bottom When the lens is shifted to rightmostReplacement of Terminal Terminals of ProjectorCables used for connection Connecting to ComputerTerminals of the projector Monitor Out Signal Table Connecting to Video EquipmentProjector Attaching the Cable Tie To loosen the cable tieFor the U.S.A. and Canada Connecting the AC Power CordFor Continental Europe What is PIN code? Basic OperationTurning On the Projector Enter a PIN codeTurning Off the Projector Remote Control How to Operate the On-Screen MenuOn-Screen Menu Menu Bar Operating with Projector Control Information Information MenuOperating with Remote Control Timer button Shutter buttonFilter button Image ADJ. buttonRemote Control Operation Input SelectionInput Side Control OperationWhen Selecting the Input 1 with DVI/D-sub 15 terminals Computer Input Source SelectionMenu Operation Input MenuRGB AV Hdcp Video Input Source SelectionPb/Cb, Pr/Cr Computer Input Computer System SelectionAutomatic Multi-Scan System Selecting Computer System ManuallyAuto PC Adjustment To store the adjusted parametersPC Adjust Menu Direct OperationManual PC Adjustment Reset Mode freeTo clear the adjusted data To store the adjusted dataImage Level Selection Standard Real Dynamic Image1 Image SEL. buttonStandard ImageScreen Size Adjustment Screen MenuKeystone CeilingRear Digital zoom +Video Input Video System SelectionVideo Jack or S-Video Jack Pb/Cb, Pr/Cr JacksStandard Cinema Dynamic Image1 Image SEL. button Natural Wide Keystone Image Adjustment Image Adjust MenuPointer Mode Picture ImageColor M MenuList Color M Menu Color PaletteWhite balance Red/Green/Blue Offset Red/Green/BlueSharpness GammaSetting SettingLamp mode BackgroundLamp control Lamp life controlPicture in Picture Edge blending Color matchingDynamicBlack Advanced color matchingHdmi setup LogoLogo select CaptureEnter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code Remote control To change the code for the remote controlTo reset the code for the remote control Filter controlPower management On startPIN code lock Security Key lockSecurity Change the PIN Code Lock setting Change the PIN CodeShutter ProtectionEffect Release keyClosed caption Video delay controlFrame lock Filter replacement icon Filter counterFactory default Test patternMaintenance and Care Filter InstructionsReset the filter counter and the scroll counter p.66 Service Parts No 350Resetting the Filter Counter Resetting the Scroll CounterFilter counter Scroll counterLamp 1/2 Replace Indicators Lamp Mode ChangeoverLamp Management Lamp Status DisplayIndicators Lamp ReplacementLamp 1 / 2 Replace indicators Lamp Handling Precautions Optional Color Wheel Installation Cleaning the Projection Lens Cleaning the Projector CabinetLamp indicator lights on and other indicators blink Then check the matters belowTroubleshooting AppendixAppendix Power is turned off Information Image Adjust Menu TreeComputer Input/Video Input NetworkPC Adjust SystemImage Select ScreenSetting Indicators and Projector Condition Projector is operating normallyProjector is detecting abnormal condition Lamp Replace 1Filter replacement icon Compatible Computer Specifications ON-SCREEN ResolutionFreq.kHz Freq.Hz Display30.000 Supported Signal Format for Optional Board List of Picture in PictureTechnical Specifications Optional Parts Input Configurations of TerminalsOutput PIN Code Lock No PIN Code Number MemoLogo PIN Code Lock No Dimensions Unit inch mmHow to adjust multiple screens Edge blendingColor matching Page Page Corporate offices