Barco 9200 owner manual Control, Front Panel Terminology

Page 11

	0I	9+]$
					Location and Functions of Control
3	LOCATION AND FUNCTIONS				OF CONTROL
Front Panel Terminology
			PROJECTOR MODE :
			GREEN - OPERATION		DIAGNOSTICS
		COMMUNICATION PORT	RED - STANDBY	IR-ACKNOWLEDGED CODE		IR-RECEIVER
	RS232 OUT	RS 232 IN (800-PERIPHERALS) REMOTE
				IR-RECEIVED

1	RS232 IN : to allow communication with external compu-
	ter, e.g. IBM PC or compatible, Macintosh ...

RS232 OUT : used to connect to next projector, RS232IN

2plug (communication link for PC or MAC to the next projector).

3	Communication port : allows communication with the
	800 peripherals.

4Remote : remote input for wired remote control.

Projector mode indication : indicates the status of the

5 projector.

Light off : power switch is not pressed.

Red light : power switch is pressed, projector in stand by mode.

Green light : projector in operational mode.

6IR-Acknowledged : IR signals are recognized.

7

8

9

10

11

12

IR-Received : IR signals are received but not recognized by the projector.

Diagnostics code : a) source number

b)error code : a two digits error code is displayed when something goes wrong inside the projector.

IR receiver : receiver for control signals transmitted from the RCU.

Power switch : '1' = on, '0' = off

Power input : autoranging from 90 to 240 Vac.

Identification plate : name, serial number, art. number.

Voltage identification plate : name, art. number.

Control Panel Terminology a. Local keypad

Gaining access

The keypad is located behind a door, screened with the name of the projector.

To open the door, push once on the indicated side of the door and turn it to the front side of the projector.

5975967 BARCOGRAPHICS 9200 030798		3-1

Image 11

Contents Graphics Page Date Rev Art. No 030798 R5975947 Barco Projection SystemsFederal communication commission FCC statement Table of Contents 11-1 10-110-2 10-4Unpacking Unpacking and DimensionsProjector dimensions Battery installation in the RCU Installation Guidelines RGB Analog with TRI-LEVEL Sync Sync on Green or Where to install the projector?How to install a projection lens? RGB Analog with Standard Sync Sync on Green orFront Panel Terminology ControlLocal keypad Remote controlRC operating indication lights up when a button on Control disc Key on RCU or + and keys cursorFront/table, front/ceiling, rear/table and rear/ceiling Actual selected configuration will be highlightedInstallation ConfigurationInstallation Set Up Fuses Power mains cord connectionSwitching on ConnectionsInput connections Switching to stand-bySwitching off Lamp Run Time269,2VIDEO,1387 Video/S-video input moduleRGB Analog Input Module 2032117B-Y S9,2,1387 Component Input ModuleRGB3S/RG3sB Input Module See Change Baudrate PC in chapter Service mode Set up of the baud rate for communication with a computerConnecting an IR Remote Receiver 800 to the projector Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector Point the front of the RCU to the reflective screen surface How to Use the RCU?Controlling Projector AddressPicture Controls with Direct Access How to Display a Projector Address?How to Program an Address into the RCU? Adjustment Mode Start UP of the Adjustment ModeStart up of the Adjustment Mode File Service Random Access Adjustment ModeStarting up the Random Access Adjustment Mode Edit file adaptation menu will be displayed File ServiceLoad File Edit FileHow to find the correct values for the displayed item? Example for clamp position trailing Copy RenameCopy RenameFile Options Picture TuningDelete Comparison with the green color value Color TemperatureSync slow/fast Still VideoSize GammaGeometry ShiftBlanking Side KeystoneBlanking Side KeystoneOptions Input Slots Starting up the Installation ModeConvergence ConvergenceRED on Green Internal Patterns ConfigurationBarcographics 9200 11-1 Service ModeStarting up the Service Mode ServiceIdentification IdentificationHow to enable or disable the password function ? Change PasswordChange Baudrate PC How to change the password ?Change Language Change Projector AddressBarcographics 9200 11-5 Reset Lamp RuntimeLamp Power Lamp Run Time HistoryI2C diagnosis Panel AdjustmentsPreset Input Balance Hz TrackingStandard Source SET UP Files 640 X 55,370 24,370 21,060 864 440 400 KHz MHz XGA72 1024 768 71,955 58,140 80,000 1376 808640 X 74,996 68,846 57,280 832 918 870 832 X 74,550 49,722 57,280 1152 667 624Lenses Focusing the lensLens Cleaning Procedure Lenses Projector with a 800 peripheral connected Projector without any 800 peripheral connectedSource numbers 81 13873525&8-6285&6&725