Barco 9200 Load File, Edit File, Edit file adaptation menu will be displayed, File Service

Page 28

Random Access Adjustment Mode

Highlight File Service by pushing the control disc up or down and press ENTER to select. The File service menu will be displayed.

ENTER displays the File Service menu;

EXIT returns to the Path selection menu.

ADJUST returns to operational mode.

The following file manupulations are possible :

-Load : installation of a file for a new source.

-Edit : editing a loaded file to the source specs.

-Rename : renaming a file.

-Copy : copying a file to a new file.

-Delete : deleting an existing file.

-Options : way of sorting the files.

RANDOM ACCESS

ADJUSTMENT MODE

FILE SERVICE

PICTURE TUNING

GEOMETRY

Select with

or

 

then

FILE SERVICE

<EXIT>

 

 

 

LOAD

 

 

EDIT

 

 

RENAME

 

 

COPY

 

 

DELETE

 

 

OPTIONS

 

 

Select with

or

 

then <ENTER>

 

<EXIT> to return.

Load File

Push the control disc up or down to select LOAD and press ENTER to display the Load menu.

The Load menu displays the corresponding files depending on the installed filter.

This filter can be "Fit" or "All". To change the filter, push the control disc to the right to select "filter list" (filter list will be hightlighted) and press ENTER to toggle the annotation between brackets.

"All" : all files that can be loaded will be displayed.

"Fit" : only the best fitting files will be displayed (with a distinction of ± 2 lines and line duration distinction of ± 300 ns, if noting is found wihtin this small area, the projector continues searching until it finds something.)

Push the control disc up or down to select the best fitting file and press ENTER to select.

When scrolling through the files, the image will be adapted according to the settings of the selected file (on line adaptation). When the best fitting image is displayed, press ENTER to select this file. A confirm Load file menu will be displayed with the newly created file and the one on which the new file is based on.

Press ENTER to confirm your new creations or EXIT to return to the load file menu.

If the displayed image is not correct, go to the Edit menu, select the active file and change the File settings.

During a load file, the actual active file is displayed next to the indication 'Active file'.

Edit File

The Edit file menu makes it possible to change the settings of the file according to the real settings of the connected source. Consult the source specification before entering the data.

To start up the EDIT menu, push the control disc up or down to select EDIT in the FILE menu and press ENTER.

Select the file which must be edited (mostly the active file) and press

ENTER.

The Edit file adaptation menu will be displayed.

FILE SERVICE

 

 

 

 

 

LOAD

 

 

 

 

 

EDIT

 

 

 

 

RENAME

 

 

 

 

 

COPY

 

 

 

 

Select with

LOAD FILE

 

FILTER LIST [All]

 

then

 

 

Filename

Src

Resolution

 

 

-----------------------------------------------------

 

ntsc

.s01

1

675x240i

 

ntsc

.c01

1

675x240i

 

ntsc_2

.s01

1

675x240i

 

-----------------------------------------------------

 

Active

file : ntsc.c50

 

 

 

 

Select with

or

,

 

 

<ENTER> to accept

 

 

 

<EXIT> to

return.

 

CONFIRM

LOAD FILE

Create

file

ntsc.c02

based

on file

ntsc.s01?

<ENTER>

to

confirm

<EXIT>

to

return

FILE SERVICE

 

 

 

 

 

LOAD

 

 

 

 

 

EDIT

 

 

 

 

RENAME

 

 

 

 

 

COPY

 

 

 

 

Select with

 

EDIT FILE

 

 

 

 

 

then

Filename

Src

Resolution

 

 

-----------------------------------------------------

 

ntsc

.s01

1

675x240i

 

ntsc

.c01

1

675x240i

 

ntsc_2

.s01

1

675x240i

 

-----------------------------------------------------

 

Active

file : ntsc.c50

 

 

 

 

Select with

or

,

 

 

<ENTER> to accept

 

 

 

<EXIT> to

return.

 

8-2

 

5975967 BARCOGRAPHICS 9200 030798

 

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Graphics Page Barco Projection Systems Date Rev Art. No 030798 R5975947Federal communication commission FCC statement Table of Contents 10-1 10-210-4 11-1Projector dimensions Unpacking and DimensionsUnpacking Battery installation in the RCU Installation Guidelines Where to install the projector? How to install a projection lens?RGB Analog with Standard Sync Sync on Green or RGB Analog with TRI-LEVEL Sync Sync on Green orControl Front Panel TerminologyRemote control RC operating indication lights up when a button onControl disc Key on RCU or + and keys cursor Local keypadActual selected configuration will be highlighted InstallationConfiguration Front/table, front/ceiling, rear/table and rear/ceilingInstallation Set Up Power mains cord connection Switching onConnections FusesSwitching to stand-by Switching offLamp Run Time Input connectionsVideo/S-video input module 269,2VIDEO,1387RGB Analog Input Module Component Input Module 2032117B-Y S9,2,1387RGB3S/RG3sB Input Module Set up of the baud rate for communication with a computer See Change Baudrate PC in chapter Service modeConnecting a VS05 to the projector Connecting a Rcvds 05 to the projectorConnecting an IR Remote Receiver 800 to the projector How to Use the RCU? ControllingProjector Address Point the front of the RCU to the reflective screen surfaceHow to Program an Address into the RCU? How to Display a Projector Address?Picture Controls with Direct Access Start UP of the Adjustment Mode Adjustment ModeStart up of the Adjustment Mode Starting up the Random Access Adjustment Mode Random Access Adjustment ModeFile Service File Service Load FileEdit File Edit file adaptation menu will be displayedHow to find the correct values for the displayed item? Example for clamp position trailing Rename CopyRename CopyDelete Picture TuningFile Options Color Temperature Sync slow/fastStill Video Comparison with the green color valueGamma GeometryShift SizeSide Keystone BlankingSide Keystone BlankingOptions Starting up the Installation Mode Input SlotsConvergence ConvergenceRED on Green Configuration Internal PatternsService Mode Starting up the Service ModeService Barcographics 9200 11-1Identification IdentificationChange Password How to enable or disable the password function ?How to change the password ? Change LanguageChange Projector Address Change Baudrate PCReset Lamp Runtime Lamp PowerLamp Run Time History Barcographics 9200 11-5Panel Adjustments Preset Input BalanceHz Tracking I2C diagnosisStandard Source SET UP Files KHz MHz XGA72 1024 768 71,955 58,140 80,000 1376 808 640 X 74,996 68,846 57,280 832 918 870832 X 74,550 49,722 57,280 1152 667 624 640 X 55,370 24,370 21,060 864 440 400Lens Cleaning Procedure Focusing the lensLenses Lenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 81 13873525&8-6285&6&725
Top Page Image Contents