Barco 9200 owner manual Battery installation in the RCU

Page 8

Unpacking and Dimensions

Battery installation in the RCU.

A battery (not yet installed to save the battery life time) is delivered inside the plastic bag with the power cord. To install the battery, remove the battery cover on the backside of the remote control by pushing the indicated handle a little to the bottom of the RCU. Lift up the top side of the cover at the same time (fig. 1).

Insert the new 9 V battery (type E-block or equivalent) in the lower compartment and connect the battery to the contact plate.

Insert the battery into the lower compartment and put the cover back.

Note : projector address has to be programmed on the RCU before using the RCU (see chapter 'Controlling').

Contact plate

Battery

fig.1

Insert here the 'Insert card RCU' which you can cut out on the last page of this manual.

fig.2

310a.DRW

1-2		5975288 BARCOGRAPHICS 8200 030798

Image 8

Contents Graphics Page Barco Projection Systems Date Rev Art. No 030798 R5975947Federal communication commission FCC statement Table of Contents 10-1 10-210-4 11-1Unpacking Unpacking and DimensionsProjector dimensions Battery installation in the RCU Installation Guidelines Where to install the projector? How to install a projection lens?RGB Analog with Standard Sync Sync on Green or RGB Analog with TRI-LEVEL Sync Sync on Green orControl Front Panel TerminologyRemote control RC operating indication lights up when a button onControl disc Key on RCU or + and keys cursor Local keypadActual selected configuration will be highlighted InstallationConfiguration Front/table, front/ceiling, rear/table and rear/ceilingInstallation Set Up Power mains cord connection Switching onConnections FusesSwitching to stand-by Switching offLamp Run Time Input connectionsVideo/S-video input module 269,2VIDEO,1387RGB Analog Input Module Component Input Module 2032117B-Y S9,2,1387RGB3S/RG3sB Input Module Set up of the baud rate for communication with a computer See Change Baudrate PC in chapter Service modeConnecting an IR Remote Receiver 800 to the projector Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector How to Use the RCU? ControllingProjector Address Point the front of the RCU to the reflective screen surfacePicture Controls with Direct Access How to Display a Projector Address?How to Program an Address into the RCU? Start UP of the Adjustment Mode Adjustment ModeStart up of the Adjustment Mode File Service Random Access Adjustment ModeStarting up the Random Access Adjustment Mode File Service Load FileEdit File Edit file adaptation menu will be displayedHow to find the correct values for the displayed item? Example for clamp position trailing Rename CopyRename CopyFile Options Picture TuningDelete Color Temperature Sync slow/fastStill Video Comparison with the green color valueGamma GeometryShift SizeSide Keystone BlankingSide Keystone BlankingOptions Starting up the Installation Mode Input SlotsConvergence ConvergenceRED on Green Configuration Internal PatternsService Mode Starting up the Service ModeService Barcographics 9200 11-1Identification IdentificationChange Password How to enable or disable the password function ?How to change the password ? Change LanguageChange Projector Address Change Baudrate PCReset Lamp Runtime Lamp PowerLamp Run Time History Barcographics 9200 11-5Panel Adjustments Preset Input BalanceHz Tracking I2C diagnosisStandard Source SET UP Files KHz MHz XGA72 1024 768 71,955 58,140 80,000 1376 808 640 X 74,996 68,846 57,280 832 918 870832 X 74,550 49,722 57,280 1152 667 624 640 X 55,370 24,370 21,060 864 440 400Lenses Focusing the lensLens Cleaning Procedure Lenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 81 13873525&8-6285&6&725