Barco 9200 owner manual Federal communication commission FCC statement

Page 4

Federal communication commission (FCC statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Instructions to the user :

if this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of the following measures :

-Re-orientation of the receiving antenna for the radio or television.

-Relocate the equipment with respect to the receiver.

-Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.

• Fasten cables connectors to the equipment by mounting screws.

Note :

The use of shielded cables is required to comply within the limits of Part15 of FCC rules and EN55022.

Due to constant research, the information in this manual is subject to change without notice.

Produced by BARCO NV, July 1998.

All rights reserved.

Trademarks are the rights of their respective owners.

BARCO n.v./Projection Systems

Noordlaan 5

B-8520 Kuurne

Belgium

Tel : +32/56/368211

Fax : +32/56/351651

E-mail : sales.bps@barco.com

Visite Barco at the web : http://www.barco.com

Printed in Belgium

Image 4

Contents Graphics Page Barco Projection Systems Date Rev Art. No 030798 R5975947Federal communication commission FCC statement Table of Contents 10-1 10-210-4 11-1Projector dimensions Unpacking and DimensionsUnpacking Battery installation in the RCU Installation Guidelines Where to install the projector? How to install a projection lens?RGB Analog with Standard Sync Sync on Green or RGB Analog with TRI-LEVEL Sync Sync on Green orControl Front Panel TerminologyRemote control RC operating indication lights up when a button onControl disc Key on RCU or + and keys cursor Local keypadActual selected configuration will be highlighted InstallationConfiguration Front/table, front/ceiling, rear/table and rear/ceilingInstallation Set Up Power mains cord connection Switching onConnections FusesSwitching to stand-by Switching offLamp Run Time Input connectionsVideo/S-video input module 269,2VIDEO,1387RGB Analog Input Module Component Input Module 2032117B-Y S9,2,1387RGB3S/RG3sB Input Module Set up of the baud rate for communication with a computer See Change Baudrate PC in chapter Service modeConnecting a VS05 to the projector Connecting a Rcvds 05 to the projectorConnecting an IR Remote Receiver 800 to the projector How to Use the RCU? ControllingProjector Address Point the front of the RCU to the reflective screen surfaceHow to Program an Address into the RCU? How to Display a Projector Address?Picture Controls with Direct Access Start UP of the Adjustment Mode Adjustment ModeStart up of the Adjustment Mode Starting up the Random Access Adjustment Mode Random Access Adjustment ModeFile Service File Service Load FileEdit File Edit file adaptation menu will be displayedHow to find the correct values for the displayed item? Example for clamp position trailing Rename CopyRename CopyDelete Picture TuningFile Options Color Temperature Sync slow/fastStill Video Comparison with the green color valueGamma GeometryShift SizeSide Keystone BlankingSide Keystone BlankingOptions Starting up the Installation Mode Input SlotsConvergence ConvergenceRED on Green Configuration Internal PatternsService Mode Starting up the Service ModeService Barcographics 9200 11-1Identification IdentificationChange Password How to enable or disable the password function ?How to change the password ? Change LanguageChange Projector Address Change Baudrate PCReset Lamp Runtime Lamp PowerLamp Run Time History Barcographics 9200 11-5Panel Adjustments Preset Input BalanceHz Tracking I2C diagnosisStandard Source SET UP Files KHz MHz XGA72 1024 768 71,955 58,140 80,000 1376 808 640 X 74,996 68,846 57,280 832 918 870832 X 74,550 49,722 57,280 1152 667 624 640 X 55,370 24,370 21,060 864 440 400Lens Cleaning Procedure Focusing the lensLenses Lenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 81 13873525&8-6285&6&725