Barco 9200 owner manual Connecting a Rcvds 05 to the projector, Connecting a VS05 to the projector

Page 22

Connections

Connecting a RCVDS 05 to the projector.

-Up to 10 inputs (20 when video inputs) with the RCVDS 05 and 90 inputs when RCVDS's are linked via the expansion module.

-Serial communication with the projector.

-Remote control buttons on the RCVDS to control the projector (source selection and analog settings).

-The selected source number will be displayed on a 2 digit display and the selected input module will be indicated with a LED on the

rear.

For more information about the use of the RCVDS 05, consult the owner's manual, order number : R5975765.

Connecting a VS05 to the projector

The VS05 can switch up to 5 Composite Video sources, 3 Super Video sources and 1 RGB analog or component video source to the projector. In addition, the audio signal proper to the source, can be switched to an audio amplifier.

Order number : R9827890

For more information about the use of the VS05, consult the VS05 owner's manual, BARCO order number : R5975245.

Connecting an IR Remote Receiver 800 to the projector.

This infrared red receiver unit makes it possible to control the projector from another room.

There is a communication line cable between the IR receiver and the projector or the RCVDS. The control information from the RCU can now be sent to the IR Remote Receiver 800.

The IR Remote Receiver 800 displays the selected source on a 7- segment display.

Order number : R9827515.

5-8		5975967 BARCOGRAPHICS 9200 221297

Image 22

Contents Graphics Page Barco Projection Systems Date Rev Art. No 030798 R5975947Federal communication commission FCC statement Table of Contents 10-4 10-110-2 11-1Projector dimensions Unpacking and DimensionsUnpacking Battery installation in the RCU Installation Guidelines RGB Analog with Standard Sync Sync on Green or Where to install the projector?How to install a projection lens? RGB Analog with TRI-LEVEL Sync Sync on Green orControl Front Panel TerminologyControl disc Key on RCU or + and keys cursor Remote controlRC operating indication lights up when a button on Local keypadConfiguration Actual selected configuration will be highlightedInstallation Front/table, front/ceiling, rear/table and rear/ceilingInstallation Set Up Connections Power mains cord connectionSwitching on FusesLamp Run Time Switching to stand-bySwitching off Input connectionsVideo/S-video input module 269,2VIDEO,1387RGB Analog Input Module Component Input Module 2032117B-Y S9,2,1387RGB3S/RG3sB Input Module Set up of the baud rate for communication with a computer See Change Baudrate PC in chapter Service modeConnecting a VS05 to the projector Connecting a Rcvds 05 to the projectorConnecting an IR Remote Receiver 800 to the projector Projector Address How to Use the RCU?Controlling Point the front of the RCU to the reflective screen surfaceHow to Program an Address into the RCU? How to Display a Projector Address?Picture Controls with Direct Access Start UP of the Adjustment Mode Adjustment ModeStart up of the Adjustment Mode Starting up the Random Access Adjustment Mode Random Access Adjustment ModeFile Service Edit File File ServiceLoad File Edit file adaptation menu will be displayedHow to find the correct values for the displayed item? Example for clamp position trailing Rename RenameCopy CopyDelete Picture TuningFile Options Still Video Color TemperatureSync slow/fast Comparison with the green color valueShift GammaGeometry SizeSide Keystone Side KeystoneBlanking BlankingOptions Starting up the Installation Mode Input SlotsConvergence ConvergenceRED on Green Configuration Internal PatternsService Service ModeStarting up the Service Mode Barcographics 9200 11-1Identification IdentificationChange Password How to enable or disable the password function ?Change Projector Address How to change the password ?Change Language Change Baudrate PCLamp Run Time History Reset Lamp RuntimeLamp Power Barcographics 9200 11-5Hz Tracking Panel AdjustmentsPreset Input Balance I2C diagnosisStandard Source SET UP Files 832 X 74,550 49,722 57,280 1152 667 624 KHz MHz XGA72 1024 768 71,955 58,140 80,000 1376 808640 X 74,996 68,846 57,280 832 918 870 640 X 55,370 24,370 21,060 864 440 400Lens Cleaning Procedure Focusing the lensLenses Lenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 81 13873525&8-6285&6&725