Barco 9200 owner manual Rename, Copy

Page 31

Random Access Adjustment Mode

Rename

To change the name of a selected file.

Use the control disc to select RENAME and press ENTER. The Rename selection menu will be displayed.

Use the control disc to select a file name and press ENTER to select.

The Rename menu will be displayed with the selected file name already filled in in the 'From file name :' area and in the 'To file name :' area.

The first character is highlighted. Push the control disc to the right or to the left to select the desired character. Change that character by pushing the control disc up or down. Numeric characters can be entered directly with numeric keys on the RCU.

Press ENTER to confirm. The renamed file is entered in the list of files. Press EXIT to return to the Rename menu selection. No changes are made.

Copy

To copy a selected file into a new file.

Use the control disc to select COPY and press ENTER. The Copy selection menu will be displayed.

Use the control disc to select a file name and press ENTER to select.

The Copy menu will be displayed with the selected file name already filled in in the 'From file name :' area and in the 'To file name :' area.

The first character is highlighted. Push the control disc to the right or to the left to select the desired character. Change that character by pushing the control disc up or down. Numeric characters can be entered directly with numeric keys on the RCU.

Press ENTER to confirm. The copied file is entered in the list of files. Press EXIT to return to the Copy selection menu. No copies are made.

FILE SERVICE

 

 

 

LOAD

 

 

 

 

EDIT

 

 

 

 

RENAME

 

 

 

COPY

 

 

 

DELETE

 

 

 

with

or

RENAME FILE

then

 

<EXIT>

Filename

Src

Resolution

 

 

-----------------------------------------------------

 

ntsc

.s01

1

675x240i

 

ntsc

.c01

1

675x240i

 

ntsc_2

.s01

1

675x240i

 

-----------------------------------------------------

 

Active

file : ntsc.c50

 

 

 

Select with

or

 

 

<ENTER> to accept

 

 

<EXIT> to

return.

RENAME FILE

Fromefile name :

ntsc.s01

To file name :

demo.c10

Select with or Reprogram with or

or numeric keys

<ENTER> to confirm

<EXIT> to return

FILE SERVICE

 

 

 

LOAD

 

 

 

EDIT

 

 

 

 

RENAME

 

 

 

COPY

 

 

 

DELETE

 

 

 

with

 

COPY FILE

then

 

 

 

 

 

<EXIT>

Filename

Src

Resolution

 

 

-----------------------------------------------------

 

ntsc

.s01

1

675x240i

 

ntsc

.c01

1

675x240i

 

ntsc_2

.s01

1

675x240i

 

-----------------------------------------------------

 

Active

file : ntsc.c50

 

 

 

Select with

or

 

 

<ENTER> to accept

 

 

<EXIT> to

return.

COPY FILE

Fromefile name :

xga_60.s03

To file name :

xga_60.c14

Select with or Reprogram with or

or numeric keys

<ENTER> to confirm

<EXIT> to return

5975967 BARCOGRAPHICS 9200 070398

 

8-5

 

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Graphics Page Date Rev Art. No 030798 R5975947 Barco Projection SystemsFederal communication commission FCC statement Table of Contents 11-1 10-110-2 10-4Projector dimensions Unpacking and DimensionsUnpacking Battery installation in the RCU Installation Guidelines RGB Analog with TRI-LEVEL Sync Sync on Green or Where to install the projector?How to install a projection lens? RGB Analog with Standard Sync Sync on Green orFront Panel Terminology ControlLocal keypad Remote controlRC operating indication lights up when a button on Control disc Key on RCU or + and keys cursorFront/table, front/ceiling, rear/table and rear/ceiling Actual selected configuration will be highlightedInstallation ConfigurationInstallation Set Up Fuses Power mains cord connectionSwitching on ConnectionsInput connections Switching to stand-bySwitching off Lamp Run Time269,2VIDEO,1387 Video/S-video input moduleRGB Analog Input Module 2032117B-Y S9,2,1387 Component Input ModuleRGB3S/RG3sB Input Module See Change Baudrate PC in chapter Service mode Set up of the baud rate for communication with a computerConnecting a VS05 to the projector Connecting a Rcvds 05 to the projectorConnecting an IR Remote Receiver 800 to the projector Point the front of the RCU to the reflective screen surface How to Use the RCU?Controlling Projector AddressHow to Program an Address into the RCU? How to Display a Projector Address?Picture Controls with Direct Access Adjustment Mode Start UP of the Adjustment ModeStart up of the Adjustment Mode Starting up the Random Access Adjustment Mode Random Access Adjustment ModeFile Service Edit file adaptation menu will be displayed File ServiceLoad File Edit FileHow to find the correct values for the displayed item? Example for clamp position trailing Copy RenameCopy RenameDelete Picture TuningFile Options Comparison with the green color value Color TemperatureSync slow/fast Still VideoSize GammaGeometry ShiftBlanking Side KeystoneBlanking Side KeystoneOptions Input Slots Starting up the Installation ModeConvergence ConvergenceRED on Green Internal Patterns ConfigurationBarcographics 9200 11-1 Service ModeStarting up the Service Mode ServiceIdentification IdentificationHow to enable or disable the password function ? Change PasswordChange Baudrate PC How to change the password ?Change Language Change Projector AddressBarcographics 9200 11-5 Reset Lamp RuntimeLamp Power Lamp Run Time HistoryI2C diagnosis Panel AdjustmentsPreset Input Balance Hz TrackingStandard Source SET UP Files 640 X 55,370 24,370 21,060 864 440 400 KHz MHz XGA72 1024 768 71,955 58,140 80,000 1376 808640 X 74,996 68,846 57,280 832 918 870 832 X 74,550 49,722 57,280 1152 667 624Lens Cleaning Procedure Focusing the lensLenses Lenses Projector with a 800 peripheral connected Projector without any 800 peripheral connectedSource numbers 81 13873525&8-6285&6&725
Top Page Image Contents