Barco 9200 owner manual Options

Page 36

Random Access Adjustment Mode

BLANKING

TOP

BOTTOM

LEFT

RIGHT

Select with or then <ENTER> <EXIT> to return.

Options

Highlight Options by pushing the control disc up or down and press ENTER. The Geometry Options menu will be displayed.

The next question will be asked by the projector :

'Use the same side keystone correction for all files ? [YES] or [NO]. [YES] : the same keystone correction will be used for all installed files. [NO] : the keystone has to be adjusted file per file.

Push the ENTER key to toggle between [YES] or [NO].

Press EXIT to return to the Geometry menu.

Adjustment of the blanking on the top of the image

Adjustment of the blanking on the bottom of the image

Correct by pushing the control disc up or down

Adjustment of the blanking on the left side

Adjustment of the blanking on the right side

Correct by pushing the control disc to the right or to the left

GEOMETRY
SHIFT
SIZE
SIDE KEYSTONE
BLANKING
OPTIONS
GEOMETRY OPTIONS
Use the same side
keystone	correction
for all	files ?
[YES]
<ENTER>	to	toggle
<EXIT>	to	return

8-10		5975967 BARCOGRAPHICS 9200 030798

Image 36

Contents Graphics Page Barco Projection Systems Date Rev Art. No 030798 R5975947Federal communication commission FCC statement Table of Contents 10-1 10-210-4 11-1Unpacking and Dimensions Projector dimensionsUnpacking Battery installation in the RCU Installation Guidelines Where to install the projector? How to install a projection lens?RGB Analog with Standard Sync Sync on Green or RGB Analog with TRI-LEVEL Sync Sync on Green orControl Front Panel TerminologyRemote control RC operating indication lights up when a button onControl disc Key on RCU or + and keys cursor Local keypadActual selected configuration will be highlighted InstallationConfiguration Front/table, front/ceiling, rear/table and rear/ceilingInstallation Set Up Power mains cord connection Switching onConnections FusesSwitching to stand-by Switching offLamp Run Time Input connectionsVideo/S-video input module 269,2VIDEO,1387RGB Analog Input Module Component Input Module 2032117B-Y S9,2,1387RGB3S/RG3sB Input Module Set up of the baud rate for communication with a computer See Change Baudrate PC in chapter Service modeConnecting a Rcvds 05 to the projector Connecting a VS05 to the projectorConnecting an IR Remote Receiver 800 to the projector How to Use the RCU? ControllingProjector Address Point the front of the RCU to the reflective screen surfaceHow to Display a Projector Address? How to Program an Address into the RCU?Picture Controls with Direct Access Start UP of the Adjustment Mode Adjustment ModeStart up of the Adjustment Mode Random Access Adjustment Mode Starting up the Random Access Adjustment ModeFile Service File Service Load FileEdit File Edit file adaptation menu will be displayedHow to find the correct values for the displayed item? Example for clamp position trailing Rename CopyRename CopyPicture Tuning DeleteFile Options Color Temperature Sync slow/fastStill Video Comparison with the green color valueGamma GeometryShift SizeSide Keystone BlankingSide Keystone BlankingOptions Starting up the Installation Mode Input SlotsConvergence ConvergenceRED on Green Configuration Internal PatternsService Mode Starting up the Service ModeService Barcographics 9200 11-1Identification IdentificationChange Password How to enable or disable the password function ?How to change the password ? Change LanguageChange Projector Address Change Baudrate PCReset Lamp Runtime Lamp PowerLamp Run Time History Barcographics 9200 11-5Panel Adjustments Preset Input BalanceHz Tracking I2C diagnosisStandard Source SET UP Files KHz MHz XGA72 1024 768 71,955 58,140 80,000 1376 808 640 X 74,996 68,846 57,280 832 918 870832 X 74,550 49,722 57,280 1152 667 624 640 X 55,370 24,370 21,060 864 440 400Focusing the lens Lens Cleaning ProcedureLenses Lenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 81 13873525&8-6285&6&725