Barco 9200 owner manual Projector without any 800 peripheral connected

Page 51

Source Numbers 90 - 99

CSOURCE NUMBERS 80 - 89 AND 90 - 99

Projector without any 800 peripheral connected.

The source numbers 80 - 89 and 90 - 99 do not correspond to physical inputs. An additional adjustment file can be created for these source numbers. This file can contain different settings. The relationship between sources 0 - 9 and 90 - 99 or between 0 - 9 and 80 - 89 is shown in the diagram below.

source input 1

source input 2

source input 3

source input 4

source number 1	file A
source number 81	file A'
source number 91	file A''
source number 2	file B
source number 82	file B'
source number 92	file B''
source number 3	file C
source number 83	file C'
source number 93	file C''
source number 4	file I
source number 84	file I'
source number 94	file I''

Follow the steps below to create a second or a third file for sources 0 to 4 :

1.Select the source between 0 and 4.

2.Select the corresponding source number between 81 and 84 and between 91 and 94 with the digit keys on the RCU.

3.Enter the adjustment mode and load a corresponding file. Edit this file if necessary.

4.Save the file and exit the adjustment mode.

Projector with a 800 peripheral connected.

Source numbers 90 - 99.

The source numbers 90 - 99 do not correspond to physical inputs. An additional adjustment file can be created for these source numbers (source numbers of the 800 peripheral). This file can contain different settings. The relationship between sources 0 - 9 of the 800 peripheral and 90 - 99 is shown in the diagram below.

	source input 1	source number 1	file A
		source number 91	file A'

	source input 2	source number 2	file B
		source number 92	file B'

	source input 3	source number 3	file C
		source number 93	file C'

	source input 9	source number 9	file I
		source number 99	file I'

Follow the same procedure as for a projector without a 800 peripheral connected.

5975947 BARCOGRAPHICS 9200 030798		C-1

Image 51

Contents Graphics Page Date Rev Art. No 030798 R5975947 Barco Projection SystemsFederal communication commission FCC statement Table of Contents 11-1 10-110-2 10-4Unpacking and Dimensions Projector dimensionsUnpacking Battery installation in the RCU Installation Guidelines RGB Analog with TRI-LEVEL Sync Sync on Green or Where to install the projector?How to install a projection lens? RGB Analog with Standard Sync Sync on Green orFront Panel Terminology ControlLocal keypad Remote controlRC operating indication lights up when a button on Control disc Key on RCU or + and keys cursorFront/table, front/ceiling, rear/table and rear/ceiling Actual selected configuration will be highlightedInstallation ConfigurationInstallation Set Up Fuses Power mains cord connectionSwitching on ConnectionsInput connections Switching to stand-bySwitching off Lamp Run Time269,2VIDEO,1387 Video/S-video input moduleRGB Analog Input Module 2032117B-Y S9,2,1387 Component Input ModuleRGB3S/RG3sB Input Module See Change Baudrate PC in chapter Service mode Set up of the baud rate for communication with a computerConnecting a Rcvds 05 to the projector Connecting a VS05 to the projectorConnecting an IR Remote Receiver 800 to the projector Point the front of the RCU to the reflective screen surface How to Use the RCU?Controlling Projector AddressHow to Display a Projector Address? How to Program an Address into the RCU?Picture Controls with Direct Access Adjustment Mode Start UP of the Adjustment ModeStart up of the Adjustment Mode Random Access Adjustment Mode Starting up the Random Access Adjustment ModeFile Service Edit file adaptation menu will be displayed File ServiceLoad File Edit FileHow to find the correct values for the displayed item? Example for clamp position trailing Copy RenameCopy RenamePicture Tuning DeleteFile Options Comparison with the green color value Color TemperatureSync slow/fast Still VideoSize GammaGeometry ShiftBlanking Side KeystoneBlanking Side KeystoneOptions Input Slots Starting up the Installation ModeConvergence ConvergenceRED on Green Internal Patterns ConfigurationBarcographics 9200 11-1 Service ModeStarting up the Service Mode ServiceIdentification IdentificationHow to enable or disable the password function ? Change PasswordChange Baudrate PC How to change the password ?Change Language Change Projector AddressBarcographics 9200 11-5 Reset Lamp RuntimeLamp Power Lamp Run Time HistoryI2C diagnosis Panel AdjustmentsPreset Input Balance Hz TrackingStandard Source SET UP Files 640 X 55,370 24,370 21,060 864 440 400 KHz MHz XGA72 1024 768 71,955 58,140 80,000 1376 808640 X 74,996 68,846 57,280 832 918 870 832 X 74,550 49,722 57,280 1152 667 624Focusing the lens Lens Cleaning ProcedureLenses Lenses Projector with a 800 peripheral connected Projector without any 800 peripheral connectedSource numbers 81 13873525&8-6285&6&725